REMS Nano Instrucciones De Servicio página 10

eng
5.3. Fault: Pipe is not cut.
Cause:
● Unsuitable cutting wheel.
● Pipe not round.
● Pipe not deburred on the outside.
● Cutting wheel damaged.
5.4. Fault: Electric pipe cutter, cordless electric pipe cutter does not start.
Cause:
● Mains lead defective (REMS Nano).
● Power tool defective.
● Worn carbon brushes.
● Battery fl at or defective (REMS Nano 11 V).
● Feeding pressure too high.
5.5. Fault: Cutting wheel becomes blunt or breaks out after 1 or 2 cuts.
Cause:
● Cutting in a cutting notch in which the previous cutting wheel already
became blunt or was damaged.
● Unsuitable cutting wheel.
● Pipe material is unsuitable for cutting.
5.6. Fault: Cutting of the pipes leaves marks on the outside of the pipes.
Cause:
● Rollers of the pipe rest (6) soiled.
● Rollers of the pipe rest (6) damaged.
6. Disposal
REMS Nano, REMS Nano 11 V, rapid charger and batteries may not be thrown
in the household waste when they are fi nished with. They must be disposed of
properly by law. Lithium batteries and battery packs of all battery systems may
only be disposed of in the discharged state, all contacts of incompletely
discharged lithium batteries and battery packs must be covered with insulating
tape.
7. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
10
Remedy:
● Select and change cutting wheel according to the pipe to be cut.
● Reduce feeding pressure.
● Deburr pipe on outside.
● Change cutting wheel.
Remedy:
● Have the mains lead changed by qualifi ed personnel or an authorised REMS
customer service workshop.
● Have the power tool checked/repaired by an authorised REMS customer
service workshop.
● Have the motor changed by an authorised REMS customer service workshop.
● Charge the battery with the rapid charger or change the battery.
● Reduce feeding pressure.
Remedy:
● Place the cutting wheel next to the notch with the remaining fragments.
● Select and change cutting wheel according to the pipe to be cut.
● Only use approved pipes, see 1.3.
Remedy:
● Clean rollers with machine cleaner REMS CleanM (Art. No. 140119), then
protect against rust.
● Change rollers.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.
8. Spare parts lists
For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng