Bosch 0601069L00 Manual Original página 13

Working Advice
Aligning with the spirit level
The laser receiver can be aligned vertically (plumb line) with
the spirit level (7). If a laser receiver is mounted at an angle,
it will give incorrect measurements.
Marking
You can mark the position of the laser beam at the centre
mark (10) on the left and right of the laser receiver when the
beam hits the centre of the reception area (11).
When marking, take care to align the laser receiver so that it
is exactly vertical (with a horizontal laser beam) or horizontal
(with a vertical laser beam), as otherwise the marks are off-
set with respect to the laser beam.
Attaching using the holder (see figure C)
You can use the holder (16) to attach the laser receiver to a
measuring rod (19) (accessory) as well as to other auxiliary
tools with a width of up to 60 mm.
Slide the holder (16) into the mount (9) on the laser re-
ceiver and click the holder into place.
Loosen the rotary knob (17) on the holder, slide the holder
onto the measuring rod (19) and retighten the rotary
knob (17).
You can use the spirit level (20) to ensure that the
holder (16) is horizontally aligned along with the laser re-
ceiver. If the laser receiver is mounted at an angle, it will give
incorrect measurements.
The centre line reference (15) on the holder is situated at
the same height as the centre marking (10) and can be used
for marking the laser beam.
To remove the holder (16) from the laser receiver,press the
unlock key (18) and pull the holder off the laser receiver.
Attaching using a magnet (see figure D)
If an attachment is not required to be especially secure, the
laser receiver can be attached to steel parts using the
magnets (8).
Fault due to strobe lighting
Prevent strobe lighting (e.g from LED lights) from reaching
the reception area (11) of the laser receiver.
In the event of a fault in the laser receiver due to strobe light-
ing, the unit of measurement indicator (d) will flash on the
display. The relative height indicator (g) and the direction
indicators (h), (i) and (j) will go out.
Move either the laser receiver or the source of the strobe
lighting to a different location.
Maintenance and Service
Maintenance and Cleaning
Always keep the laser receiver clean.
Do not immerse the laser receiver in water or other liquids.
Wipe off any dirt using a damp, soft cloth. Do not use any de-
tergents or solvents.
Bosch Power Tools
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The laser receiver, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of laser receivers or batteries
with household waste.
Only for EU countries:
According to the Directive 2012/19/EU on waste electrical
and electronic equipment and its transposition into national
law, laser receivers that are no longer usable, and, according
to the Directive 2006/66/EC, defective or drained batteries
must be collected separately and disposed of in an environ-
mentally correct manner.
If disposed incorrectly, waste electrical and electronic
equipment may have harmful effects on the environment and
human health, due to the potential presence of hazardous
substances.
Only for United Kingdom:
According to Waste Electrical and Electronic Equipment Reg-
ulations 2013 (2013/3113) and the Waste Batteries and
English | 13
1 609 92A 7LL | (02.05.2022)