EINHELL GE-CT 36/30 Li E Manual De Instrucciones página 12

2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6. Operation
Please note that the statutory regulations
governing noise abatement may diff er from one
location to another.
Danger! The safety guard must be fi tted when
carrying out work.
6.1 Switching the equipment on and off ,
adjusting the speed (Fig. 12)
Switching on and adjusting the speed
Press the safety lock-off (3) forward and press
the On/Off switch (2) at the same time. Adjust the
speed during operation by pressing the On/Off
switch to a greater or lesser extent. The harder
you press, the higher the speed.
Switching off
Release the On/Off switch.
6.2 Practical tips
Practice all the work steps with the motor
switched off and without the batteries installed
before you start to use the equipment. Only ever
cut grass that is dry. If the grass is long, the grass
must be cut shorter in stages (Fig. 13).
Extending the cutting line (Fig. 14)
Danger! Do not use any kind of metal wire or
metal wire encased in plastic in the line spool.
This may cause serious injuries to the user.
The string trimmer has a semi-automatic line
extension system (automatic jog line feed).
Each time you activate the semi-automatic
line extension system, the line is automatically
Anl_GE_CT_36-30_Li_USA_SPK7.indb 12 Anl_GE_CT_36-30_Li_USA_SPK7.indb 12
EN
extended to ensure that you can cut your lawn
with the perfect cutting width at all times. To
extend the cutting line, run the motor and tap the
line spool on the ground. This will automatically
extend the line. The blade on the safety guard
will cut the line to the permissible length. Please
note that the more often you activate the semi-
automatic line extension system, the more the line
will wear.
Note: If the line is too long when you use the
equipment for the fi rst time, the surplus end of it
will be cut by the blade on the safety guard. If the
line is too short when you start the equipment
for the fi rst time, press the knob on the line spool
and pull the line hard. When you then start the
machine for the fi rst time the line will be cut to the
perfect length automatically.
Using a brush or similar, carefully remove all
residual grass from the underside of the safety
guard at regular intervals.
Diff erent cutting methods
Caution! To use the edge guide along walls or
objects, swing the edge guide forward to the front
(Fig. 4). Swing it up when not in use (Fig. 15).
Please note: Even if it is used carefully, cutting
around foundations, stone or concrete walls, etc.
will result in the line suff ering above normal wear.
Trimming/mowing
Swing the trimmer from side to side in a scything
motion. Always keep the line spool parallel to the
ground. Check the site and decide what cutting
height you require. Guide and hold the line spool
at the required height to ensure that you cut
evenly.
Low trimming
Hold the trimmer right in front of you at a slight
angle so that the underside of the line spool is
above the ground and the line strikes the correct
target. Always cut away from yourself. Never draw
the trimmer towards yourself.
Cutting along fences/foundations
Edge guide recommended!
When cutting, approach wire mesh fences, lath
fences, natural stone walls and foundations
slowly so that you can cut close to them without
striking the obstacle with the line. If, for example,
the line strikes stones, stone walls or foundations,
it will wear or fray. If the line strikes wire fencing it
will break.
- 12 -
06.12.2022 09:48:37 06.12.2022 09:48:37