Bosch 0 601 B22 503 Manual Original página 35

All manuals and user guides at all-guides.com
OBJ_BUCH-1128-004.book Page 35 Wednesday, April 15, 2015 4:58 PM
Setting the Standard 45° Bevel Angle (Rightward)
– Bring the power tool into the working position.
– Turn the saw table 16 to the 0° detent 15. The lever 13
must be felt to engage in the detent.
– Pull the right fence extension 19 completely outward.
– Loosen the lock lever 14.
– Lightly tilt the tool arm leftward out of the 0° position via
handle 5 and turn knob 39 until the bevel angle range
is indicated.
0 – 45°
– Tilt the tool arm via handle 5 rightward to the stop (45°).
Checking: (see figure U1)
– Set an angle gauge to 135° and place it on the saw table 16.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Adjusting: (see figure U2)
– Guide the supplied hex key 43 (3 mm) from outside
through the smaller hole in the housing and insert it into
the covered set screw 65.
– Screw the set screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever 14 again.
When the angle indicators 31 and 22 are not in line with the
45° marks of scale 30 after adjusting, firstly once more check
the 0° setting for the bevel angle and the angle indicators.
Then repeat the adjustment of the 45° bevel angle.
Adjusting the Clamping Force of Lock Lever 14
(see figure T2)
The clamping force of lock lever 14 can be readjusted.
Checking:
– The clamping force of the clamping lever must securely
hold the position of the tool arm at any bevel angle.
Adjusting:
– Loosen the lock lever 14.
– Turn set screw 66 in anticlockwise direction with the sup-
plied open-end spanner 42 (17 mm) to reduce the clamp-
ing force, or increase the clamping force by turning in
clockwise direction.
– Adjust a vertical bevel angle, retighten lock lever 14 and
check if the desired clamping force has been reached.
Adjusting the Clamping Force of Clamp 3 (see figure V)
The clamping force of the handle clamp 3 can be readjusted.
Checking:
– The clamping force of the clamp must securely hold the
handle in any of the 4 possible positions.
Adjusting:
– Open clamp 3.
– Turn both set screws 67 in anticlockwise direction with the
supplied hex key 44 (1,5 mm) to reduce the clamping
force, or increase the clamping force by turning in clock-
wise direction.
Always adjust both set screws to the same height.
– Shut clamp 3 and check if the desired clamping force has
been reached.
Bosch Power Tools
Aligning the Angle Indicator (Horizontally) (see figure W)
– Bring the power tool into the working position.
– Turn the saw table 16 to the 0° detent 15. The lever 13
must be felt to engage in the detent.
Checking:
The angle indicator 68 must be in alignment with the 0° mark
of the scale 38.
Adjusting:
– Loosen the fastening screw of the angle indicator with the
supplied cross-head screwdriver 33 and align the angle in-
dicator alongside the 0° mark.
– Retighten the screw again.
Aligning the Fence
– Bring the machine into the transport position.
– Turn the saw table 16 to the 0° detent 15. The lever 13
must be felt to engage in the detent.
Checking: (see figure X1)
– Adjust an angle gauge to 90° and position it flush with the
saw blade 7 between the fence 18 and the saw blade on
the saw table 16.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting: (see figure X2)
– Loosen the locking screws 20 on bothe sides of the fence
extensions 19.
Loosen the setting screws 69 with the supplied hex key 33
(4 mm).
– Remove the fence extensions.
– Loosen all hex socket screws 70 with the supplied socket
spanner 33 (14 mm).
– Turn the fence 18 until the angle gauge is flush over the
complete length.
– Retighten the hex socket screws 70.
– Retighten the fence extensions. Tighten the setting screws
69 only to the extent, that the fence extensions can be
moved easily.
Transport (see figure Y)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 29 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Carry the power tool by the transport handles 28 and 2 or
via the recessed grips 71 on the side of the saw table.
 The power tool should always be carried by two per-
sons in order to avoid back injuries.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.
English | 35
1 609 92A 19J | (15.4.15)