Ryobi EHP-4011 Uso Y Mantenimiento página 10

interno1e 4-02-2003
8
English
a - Water outlet (OULET)
b - Water inlet with filter (INLET)
c - High pressure rotating nozzle kit
(optional accessory)
d - Adjustable spray nozzle
e - Use • Maintenance handbook
f - Power supply cable with plug
g - Lance
h - Gun with safety catch
i - High pressure hose
m - Nozzle cleaning tool
n - Motor switch
p - Adjustable foam unit
3 GENERAL RULES
3.1.1 The USE and MAINTENANCE manual
constitutes an essential part of the cleaner
equipment and should be kept in a safe
place for future reference. If you sell the
cleaner, the manual should be handed on
to the new owner.
3.1.2 Before starting the cleaner, make sure that
it is receiving water correctly. Operating
the cleaner without water could damage
the seals.
3.1.3 Do not disconnect the plug by pulling on
the electrical cable.
3.1.4 If you are too far from the object you wish
to clean, do not move the cleaner nearer
by pulling on the high pressure hose; use
the handle provided.
3.1.5 In versions not equipped with TSS
device, do not operate the cleaner for
more than 1-2 minutes with the gun
closed as this could damage the seals.
3.1.6 Protect the cleaner from freezing during
the winter.
3.1.7 Do not obstruct the ventilation grilles dur-
ing operation.
3.1.8 The cross-section of any exten-
sion cables used must be propor-
tional to their length, i.e. the longer the
extension cable, the greater the cross-
section; cables with a protection level
of "IPX5" must be used. See table a for
Voltage
Volts
220 - 230
240
MOTOR
100 - 115
120
details.
Table a.
3.1.9 Position the cleaner AS NEAR AS POS-
SIBLE to the water supply.
3.1.10 The packaging is easily recyclable, and
18:44 Pagina 8
Extension Extension
cable cable
up to 25 m up to 50 m
section section
3x1.5 mm 3x2.5 mm
2 2
section section
3x2.5 mm 2 3x4 mm 2
must be disposed of in compliance with
the regulations in force in the country of
installation.
3.1.11 Use the cleaner only with accessories and
replacement parts authorised by the man-
ufacturer. The use of original accessories
and replacement parts will ensure safe,
trouble-free operation.
3.1.12 The cleaner must be used standing on
a secure, stable surface, positioned as
shown. FIG.3A
3.2 INTENDED USE
3.2.1 The cleaner is intended only for the clean-
ing of vehicles, machines, boats, build-
ings, etc., by the removal of stubborn dirt
using clean water and chemical deter-
gents.
3.2.2 When using chemical detergents, only
use biodegradable types.
We recommend HOBBY - FOAM deter-
gent (# 3206).
3.2.3 Only clean vehicle engines in areas in
which suitable oil traps are installed.
3.3 SAFETY VALVE
3.3.1 The safety valve also functions as a pres-
sure limiting valve. When the gun trigger is
released, the safety valve opens and the
water recirculates through the pump inlet.
4 INSTALLATION
4.1 Fit the lance into the gun by rotat-
ing and pushing until the two
parts are completely locked. FIG.4A
4.2 Connect the gun to the high pressure
hose. FIG.4B
4.3 Connect the high pressure hose to the
water (OUTLET) on the cleaner. FIG.4C
4.4 Connect the water supply hose FIG.4D
(not supplied) to the water (INLET) of the
cleaner. The supply hose must have an
internal diameter of at least 13 mm (1/2
in.) and must be reinforced. The water
supply must be at least equal to the clean-
er delivery capacity.
The intake water tempera-
ture must NOT exceed 50°C
(122°F). The water supply pressure
must NOT exceed 10 bar (145 psi).
4.4.1 CAUTION! The cleaner must only
be used with clean water; use of
unfiltered water or corrosive chemicals
will damage the cleaner.
4.5 Turn the motor switch to the "0" position.
4.6 Check that the electrical supply voltage
and frequency (Volts/Hz) correspond to
those specified on the cleaner data plate.
FIG.3B
If the power supply is correct, you may