Elvox 6600 Serie Manual Para El Conexionado Y El Uso página 6

GB
DESCRIPTION
Type 6601 is a 6600 series open-voice video interphone with 4" colour
LCD screen for ELVOX 2-WIRE video door entry systems. The monitor
has a tilting screen and is supplied as standard with 8 push-buttons for
the following functions: door lock release, self-start of video interphone
in the system even when it has not been called, conversation, stair light,
internal voice line volume control, ringtone volume control, brightness
control and ringtone type setting. Two LEDs (red and green) on the video
interphone serve to indicate the following states: call signal mute, unan-
swered calls, services not available and gate/door open.
Flush-mounting of the video interphone requires the use of flush-moun-
ted back box type 6149 or the brackets type. R660 (for plasterboard).
Fig. 1
C
D
F
G
D L
Video interphone technical specifications
- Flush-mounted video interphone in ABS.
- Removable terminal block.
- Flat 4" LCD screen.
- Electronic circuit on interchangeable cards.
- PAL standard video signal.
- Operating temperature from 0° to +40° C.
- Electronic ringtone.
- Input for landing calls with different ringtone from entrance panel calls.
- Output for additional ringtone type 860A.
- Supply voltage provided by bus.
- Input for additional power supply (type 6923) if the system is configu-
red to enable simultaneous activation of more than two monitors.
Controls and adjustments
A) Manually tilting 4" LCD screen.
B) Microphone.
C) Loudspeaker.
D) Pair of push-buttons.
1) When the monitor is ON, the push-buttons can be used to adjust
the brightness.
2) When the monitor is OFF, the push-buttons can be used to select
the tune for calls from a speech unit only. To programme the tune:
hold down 1 of the 2 push-buttons for at least 1 second, then press
the push-buttons repeatedly to select the desired tune.
E) Pair of push-buttons.
1) During conversation, with push-button "i" pressed, press push-
buttons "E" to increase or decrease the volume of the internal voice
line.
2) To adjust ringtone volume: hold down 1 of the 2 push-buttons "E"
for at least 1 second, then press the push-buttons repeatedly to
increase or reduce ringtone volume, or mute the ringtone.
F) Push-button for auxiliary service, 1st relay of 1st actuator
type 692R
6
Press to return to index Press to return to index
I N T R O D U C T I O N / I N S T A L L A T I O N
A
B
E
H
I
M E
G) Push-button : for door lock release.
H) Push-button : for self-start of the monitor without the latter being
called.
I) Two-channel conversation push-button: after the monitor has
been called and/or switched on, hold down the push-button for con-
versation with the entrance panel. 5 seconds after the push-button is
released, the interphone is disconnected. If it is pressed again befo-
re the elapse of 5 seconds, conversation can continue.
L) 'Door open' LED: in systems in which this function is used, the
LED remains steadily lit when the door/gate is open
M) 'Ringtone mute' LED: the LED illuminates steadily when the rin-
gtone has been muted (see point "E") and flashes when calls have
been denied.
N.B. On the back of the video interphone is a RESET push-button for
use during programming, a trimmer for adjusting the colour, and connec-
tors A-B-C-D for stabilising the video signal.
Connection and connector terminal board
+12, CH) Additional ringtone connection.
B1, B2) BUS line.
E+, E- ) Additional supply voltage for monitor with power supply type
6923.
FP, M) Connection for landing call push-button.
INSTALLATION 6601
- Install the video interphone away from sources of light and heat.
- Flush-mount back box type 6149 in the wall at a height of approxima-
tely 1.4 m above the ground.
- Remove the plastic cross-piece from the back box
- Fix the video interphone to the back box with the 4 screws supplied
(fig. 2).
- Fit the side panels, taking care that the panel with the slot for the
microphone is fitted on the right (fig. 2).
Flush-
mounted
version
141
139 136
59 10
Fig. 2