Scheppach HSM3500 Traduccion Del Manual De Instrucciones Originale página 29

SPECIAL SAFETY INFORMATION
Caution! This stone and tile cutter is designed for wet
cutting only. The machine may be operated only with a
non-segmented diamond cutting wheel.
• Wet hands: Never touch the electrical components
of the machine (e.g. switches) with wet hands.
• Plug-in connections: All plug-in connections must
be located in a dry place and must not lie on the
floor.
• Cooling the cutting wheel: Make sure that the cut-
ting wheel is cooled with water during the complete
cutting process.
• Dry cutting: Never carry out dry cuts with cutting
wheels designed for wet cutting.
• Dust protection: Always wear a protective dust
mask when cutting tiles.
• Diamond cutting wheels: Do not feed the tile into the
machine any faster than the cutting wheel can cut.
• Use only cutting wheels which are designed for a
minimum speed of 3000 min-1.
• Selecting the cutting wheel Select the diamond
cutting wheel to suit the material you want to cut.
Fitting the cutting wheel: Before you install the cut-
ting wheel, check the spindle, the spindle nut and
the flanges for damage, wear or a loose fit. Replace
damaged or worn parts without delay.
• Direction of rotation of the cutting wheel: Check the
direction arrow on the cutting wheel; the arrow must
point in the same direction as the direction in which
the motor shaft rotates.
• Cutting wheel spindle: Make sure that the diameter
of the hole in the cutting wheel is the same as the di-
ameter of the cutting wheel spindle on the machine.
• Cutting wheel guard: Only use the stone and tile
cutter with a properly fitted and adjusted cutting
wheel guard.
• Cutting wheel speed: Do not exceed the safe oper-
ating speed of the cutting wheel.
• Sanding/grinding with the cutting wheel Do not try to
use the cutting wheel for sanding or grinding jobs,
e.g. to sand/grind the edge of a cut tile. Also, do not
use the machine for radius cuts or round cuts. This
tile cutting machine is suitable only for household
use.
• Cutting wheel stop time: After the machine has been
switched off, the cutting wheel needs 20 seconds to
come to a standstill. Wait until the cutting wheel has
stopped completely, pull the power plug out of the
socket outlet, and only then touch the cutting wheel
if necessary.
• Avoid all contact with the rotating cutting wheel
when the machine is in operation.
• The electric tool must never be used without the
PRCD plug supplied with it.
• Keep water away from electrical parts of the tool
and from persons in the work area!
• If the power plug or the power cable are damaged
they must be replaced either by the manufacturer or
by a service company authorized by the manufac-
turer.
• To comply with the requirements imposed by the
safety regulations, all technical modifications which
change the equipment's characteristics (e.g. speed)
must be left strictly to the manufacturer.
• Keep this safety information in a safe place.
Special safety instructions for stone cutting ma-
chines
• Place the stone cutting machine on a level work sur-
face with stable footing before using it. Ensure that
there is sufficient room for freedom of movement.
• In order to avoid a dust hazard, the machine may
only be used in the wet area.
• Always fill the tube with water before working.
• The machine may only be operated in sufficiently
ventilated rooms.
• Attention! Never leave the motor running in closed
or spatially-constrained rooms. The exhaust gases
contain toxic carbon monoxide!
• As a basic rule, switch on the equipment before ma-
terial contact.
• The elevated safety regulations for wet operation
apply for this stone cutting machine. All safety
measures to prevent elevated contact voltages must
be applied.
• Electrical cable wires may not come into contact
with water or water vapour.
• Before commencing work, check the equipment and
mains cable for damage.
• Check whether the moving parts function faultless-
ly and do not jam and make sure that no parts are
damaged.
• The mains voltage must match the specifications on
the type plate of the machine.
• Only use approved extension cables for use out-
doors.
• When using a cable reel, completely unwind the ca-
ble in order to prevent the cable from heating up.
• When working outside, the electrical outlet must be
equipped with a residual current circuit breaker.
www.scheppach.com GB | 29