Pioneer DJM-700-S Manual De Instrucciones página 11

NAMES AND FUNCTIONS OF PARTS
31 Headphones jack (PHONES)
Connect to headphones equipped with phone-type jack.
32 Beat select buttons ( BEAT
(Beat up):Doubles the calculated BPM.
(Beat down):Halves the calculated BPM.
(P. 18)
• Some effects can be set for "3/4".
With some effects, these are used for functions other than setting
the beat.
33 MIDI ON/OFF button
Sets MIDI output function (not including timing lock) to ON/OFF.
When power is first turned ON, automatically defaults to OFF.
34 MIDI start/stop button (MIDI START/STOP)
Outputs START/STOP signal for MIDI control function (see P. 21).
When this control is enabled, the [MIDI START (STOP)] message
appears for two seconds on the display.
MIDI SNAP SHOT:
When the MIDI START/STOP button is held depressed, a snapshot
is sent to the external MIDI component.
35 BPM measuring mode button (AUTO)
Switches between the BPM measuring modes AUTO and TAP.
When [AUTO] indicator on the display is lighted, the BPM will be
measured automatically.
36 TAP button
The BPM is calculated from the intervals at which the TAP button
is struck. If the TAP button is pressed in the AUTO mode, the mode
automatically switches to the TAP mode (manual input).
37 MANUAL/EFFECT Frequency filter button
Use to switch between manual filter and effect frequency filter.
When power is first turned ON, defaults to effect frequency filter
and the button indicator lights. When manual filter is selected, the
button indicator does not light.
38 Manual filter adjust dial (FREQUENCY)
Use to adjust the cutoff frequency of the selected filter.
39 Effect selector (DELAY, ECHO, TRANS, FILTER, FLANGER,
PHASER, REVERB, ROBOT (ROBOT VOCODER), CRUSH, ROLL,
REVERSE (REVERSE ROLL), UP (UP ROLL), DOWN (DOWN
ROLL), SND/RTN (SEND/RETURN))
Use to select desired type of effect (P. 16).
When using an external effector connected to the SEND and
RETURN connectors, set to the [SND/RTN] position.
40 Effect channel selector (1, 2, 3, 4, MIC, CF.A, CF.B, MASTER)
Use to select the channel to which effects are applied (P. 18).
When [MIC] is selected, effects are applied to both microphone 1
and microphone 2.
41 Effect parameter 1 dial [TIME (PARAMETER 1)]
Adjusts time parameter for selected effect (P. 18, 20) (With some
effects, this is used for adjustments other than time parameters.)
• If the TIME dial is rotated while depressing the TAP button,
direct BPM can be set manually.
• If the TIME dial is rotated while holding the TAP button and
AUTO/TAP buttons depressed, the BPM can be set in 0.1 units.
42 Effect parameter 2 dial [LEVEL/DEPTH (PARAMETER 2)]
Adjusts quantitative parameters for selected effect (P. 18, 20).
43 Effect button/indicator (ON/OFF)
Sets selected effect ON/OFF (P. 18). When power is first turned
ON, defaults to effect OFF. When set to effect OFF, the button
indicator lights. When effects are enabled (ON), the button
flashes.
44 Display
See the following section for details.
)
DISPLAY SECTION
1 2 3 4
AUTO
TAP
1 Effects display section
Text display (7 characters) displays effect name as shown in
accompanying table. Also, when one of the change operations is
performed as noted in the table, the corresponding characters are
displayed for two seconds, after which the display returns to the
original effect name.
Switching Operation
At MIDI start
At MIDI stop
MIDI snapshot
When MIDI output function is ON
When MIDI output function is OFF
2 Channel select display section
Lights position selected by effect channel selector.
3 Parameter display section
AUTO/TAP:
[AUTO] lights when the BPM measuring mode is set to AUTO, and
[TAP] lights when the BPM measuring mode is set to manual
(TAP).
BPM counter display (3 digits):
In AUTO mode, displays the automatically detected BPM value. If
the BPM count cannot be detected automatically, the display will
flash at the previously detected value. In manual (TAP) mode,
displays the BPM value designated by TAP input, etc.
BPM:
Lights constantly.
MIDI:
Indicates status of MIDI output function ON/OFF.
• Lights when MIDI output function is ON.
• Not lighted when MIDI output function is OFF.
Parameter 1 display (5 digits):
Displays parameters designated for each effect. When the beat
select buttons ( BEAT
, ) are pressed, the corresponding beat
multiple change is displayed for two seconds. If the beat select
buttons ( BEAT
, ) are used to designate a value outside the
parameter range, the current number will flash but will not
change.
Unit Display (%/ms):
Lights in accordance with the unit used for each effect.
1
A B M
2
MIDI
BPM
3
%
mS
4
Display
START
STOP
SNAP
MIDI On
MIDIOff
11
En