Publicidad
Idiomas disponibles
Idiomas disponibles
Advanced programming
4.
ADVANCED PROGRAMMING
4.1
PROGRAMMING PARAMETERS
IMPORTANT! Before you start programming parameters, make sure that the gate is CLOSED and STOPPED and
that the SELF-TEACH procedure has been completed.
To program the parameters, follow the instructions given in Fig. 7 and Tab. 2 below.
!
Warning
All input signals will be ignored during programming.
Press and hold down the RED button until the letter P appears on the display. Release the button
a programmable parameter will appear on the display.
To scroll through the parameters, press the BLUE button.
To leave the programming mode and return to normal operation, press the YELLOW button.
To display the current parameter value (shown by a bright dot), press the RED button;
available, press the BLUE button.
To modify a value, press the RED (Confi rm) buttonfor 3 seconds when the value required is displayed
is displayed (confi rmed by 3 fl ashes) and the system leaves the programming mode and returns to normal operation.
If you decide not to modify a value, press the YELLOW button. The display will return to showing the initial letter of the parameter.
Note: The OPERATING MODES and the signal responses are described in sect. 5.1.
Fig. 7
Red to enter
programming
mode
Tab. 2
: wing closing delay
0 = 4 seconds (*)
Note: the delay
1 = 8 seconds
time on opening
2 = 12 seconds
is fi xed at 3
3 = 16 seconds
seconds.
:
short inversion (ms.)
0 (*R)
0
1
30
2 (*S)
50
3
80
4
100
5
120
6
150
7
200
8
300
9
400
: approach time (sec.)
0 = 2
1 = 4 (*R)
2 = 5
3 = 6 (*S)
4 = 7
5 = 8
6 = 10
7 = 12
8 = 14
9 = 16
IMPORTANT NOTE:
Blue
To select
Release
Blue
to select parameter
to be modifi ed
: thrust force
0 = Low
1 = Medium
2 = High (*)
3 = Very high
4 = Medium wind
5 = Strongly wind
:
prefl ashing
reverse stroke
0 (*)
no
1
no
2
yes
3
yes
4
no
5
no
6
yes
7
yes
:
Pause time
photocell
0 (*)
NO
1
NO
2
YES
3
YES
4
NO
5
YES
Yellow
Red
To confi rm
To exit
Red
to confi rm
to select
parameter
new value
CAUTION: any increase in this
parameter causes a reduction in
obstacle recognition sensitivity.
If a value of 3, 4, or 5 is set,
use special detection devices
on the basis of correct risk
assessment.
trhust at end
of movement
no
no
yes
no
no
no
yes
no
no
yes
yes
yes
no
yes
yes
yes
Input function
J1 pin 6-9
PEDESTRIAN START
OPENING SAFETY SAFETY EDGE
PEDESTRIAN START
OPENING SAFETY SAFETY EDGE
OPENING SAFETY PHOTOCELL
OPENING SAFETY PHOTOCELL
(
) = default values for RAIDER and SKIPPER)
*
(
*R
) = default for RAIDER only
(
*S
) = default for SKIPPER only
- 20 -
the initial letter of
to scroll through the values
the new value
Blue
Red
to confi rm
new value
: Operating mode
0 = AUTOMATIC (*)
1 = 4 STEPS
2 = SUPER AUTOMATIC
3 = SEMIAUTOMATIC with STOP
4 = STEP-BY-STEP
: wing travel speed
0 = 50%
1 = 70%
2 = 85% (*S)
3 = 100% (*R)
CAUTION When the S (speed)
parameter is changed, you must
perform the self-teach procedure again.
To do this, press and hold down the
YELLOW and BLUE buttons together
for a few seconds (see section 3.1).
: pause time (sec.)
0 = 0
1 = 5 (*)
2 = 10
3 = 15
4 = 20
5 = 25
6 = 30
7 = 35
8 = 40
9 = 45
Publicidad
