Publicidad
Idiomas disponibles
Idiomas disponibles
5.
1/2" tool holder
6.
Direction selector switch
7.
Battery
8.
Battery lock button
9.
LED diodes
10. Charger
11. Button for battery level indication
12. Battery level indicator (LED)
13. Holder
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
WARNING
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Set the direction selector switch (6) in the middle position.
• Press the battery lock button (8) and slide out the battery (7) (fig. A).
• Insert charged battery (7) into the handle holder, you should hear when
the battery lock button (8) snaps.
BATTERY CHARGING
The device is supplied with partially charged battery. Charge the battery when
ambient temperature is within range 4°C–40°C. New battery, or one that has
not been used for a long time, will reach full efficiency after approximately 3
to 5 charge/discharge cycles.
• Remove the battery (7) from the device (fig. A).
• Connect the charger (10) to mains socket (230 V AC).
• Slide the battery (7) into the charger (10) (fig. B). Make sure the battery is
properly fitted (pushed to the end).
When the charger is connected to a mains socket (230 V AC), the green diode
(9) on the charger turns on to indicate connected supply.
When the battery (7) is placed in the charger (10), the red diode (9) on the
charger turns on to indicate that the charging is in progress.
At the same time green diodes (12) of the battery level indication are flashing
in different configurations, see description below.
• All diodes are flashing – the battery is empty and requires charging.
• 2 diodes are flashing – the battery is partially discharged.
• 1 diode is flashing – the battery level is high.
Once the battery has been charged, the diode (9) on the charger lights green,
and all battery level diodes (12) light continuously. After some time (approx.
15 s) the battery level indication diodes (12) turn off.
Do not charge the battery for more than 8 hours. Exceeding this
time limit may cause damage to battery cells. The charger does not turn
off automatically when the battery is full. Green diode on the charger
will remain on. Battery level indication diodes turn off after some time.
Disconnect power supply before removing the battery from the charger
socket. Avoid consecutive short chargings. Do not charge the battery after
short use of the tool. Significant decrease of the period between necessary
chargings indicates that the battery is worn out and should be replaced.
Batteries heat up when charging. Do not operate just after charging –
wait for the battery to cool down to room temperature. It will prevent
battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with indication of the battery level (3 LED diodes)
(12). To check battery level status, press the button for battery level indication
(11) (fig. C). When all diodes are lit, the battery level is high. When 2 diodes are
on, the battery is partially discharged. When only one diode is lit, the battery is
discharged and must be recharged.
SPINDLE BRAKE
The power tool is equipped with electronic brake, which stops the spindle
immediately after the switch button (4) is released. The brake allows for
precise driving and prevents free spindle rotation after switching off.
OPERATION / SETTINGS
SWITCHING ON / OFF
Switching on – press the switch button (4).
Switching off – release the switch (4).
Each time the switch button (4) is pressed, the LED diode (1) turns on to
illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (4) to adjust rotational
speed while operating. Speed control allows for soft start, which provides
working control during tightening and undoing bolts.
CHANGE OF GEAR
The tool features electronic gear change (fig. D). Clockwise operation is
possible at one of three gears, selected with the button (3). Diodes (2) turn
on individually to indicate operating gear. Increase or reduce pressure
on the switch button (4) to adjust rotational speed while operating.
After switching the direction selector switch (6), two gears are available. The
first gear, with diode (2) lit, speeds up the wrench to maximum speed and slows
down. After selecting the second gear the diode (2) turns off, and the wrench
speed is adjustable up to the maximum with pressure on the switch button (4).
CIRCUMFERENTIAL IMPACT ACTION
The tool rotates the spindle when tightening, and creates circumferential
impact. Impact action actuates automatically when the load increases. Then
a high peak torque is applied. Keep watching the screw or bolt for full control
over tightening. Keep control over tightening force by adjusting rotational
speed.
WORKING TOOL INSTALLATION
• Slide a correctly sized socket onto the 1/2" tool holder (5) as far as possible,
you should hear the ring snaps on (fig. E).
• Pull the socket lightly to make sure it is fixed properly.
Deinstallation of the tool is similar to installation, only the sequence of actions
is reversed.
We recommend to use appropriate sockets designed for use with impact
wrenches.
RIGHT-LEFT DIRECTION OF ROTATION
Use the direction selector switch (6) to choose direction of the spindle
rotation (fig. F).
Clockwise rotation – move the switch (6) to the far left position.
Counter-clockwise rotation – move the switch (6) to the far right position.
* In certain cases position of the switch related to rotation may be different than specified.
Please refer to graphic signs located on the switch or tool body.
Safe position of the direction selector switch (6) is in the middle, it prevents
accidental starting of the power tool.
• When the switch is in this position, the power tool cannot be started.
• Use this position of the switch to change sockets.
• Make sure that the position of the direction selector switch (6) is correct
before starting the tool.
Do not change direction of rotation when the spindle of the power
tool is rotating.
Long lasting operation at low rotational speed of the spindle may cause
motor overheating. Make periodic breaks in operation or allow the tool
to operate at top speed without load for approximately 3 minutes.
HOLDER
The power tool provides convenient holder (13) that allows to e.g. hang the
tool on a tool belt when working at heights.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the power tool, battery and charger with a dry cloth or blow through
with compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent device
overheating.
• Always store the power tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by the
manufacturer.
9
Publicidad
