EINHELL TE-ID 500 E Manual De Instrucciones Original página 14

Anleitung_TE_ID_500_E_SPK8__ 10.12.14 13:42 Seite 14
GB
danger posed by dust.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able to
work better and more safely within the given
performance boundaries.
b) Do not use an electric tool with a defective
switch. An electric tool that cannot be switched
on or off is dangerous and must be repaired.
c) Pull the plug out of the socket and/or remove
the battery before making any adjustments to
the appliance, changing accessories or put
the appliance down. This safety measure
prevents starting the electric tool unintentionally.
d) Keep unused electric tools out of the reach
of children. Do not allow people who are not
familiar with the appliance or who have not
read these instructions to use the appliance.
Electric tools are dangerous if they are used by
inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts are
broken or damaged enough that the
functioning of this electric tool is affected.
Have damaged parts repaired before using
the appliance. Many accidents are caused by
badly maintained electric tools.
f) Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accessories,
attachments, etc. in accordance with these
instructions. Take the conditions in your work
area and the job in hand into account. Using
electric tools for any purpose other than the one
for which they are intended can lead to
dangerous situations.
5. Service
a) Have your electric tool repaired only by
trained personnel using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Safety information for drills
Wear ear plugs when using hammer drills.
n
The impact of noise can cause damage to
hearing.
Use the additional handles supplied with the
n
tool. Losing control of the machine can cause
injuries.
14
Hold the tool by the insulated handles when
n
carrying out work during which the plug-in
tool could strike concealed power cables or
its own mains lead. Contact with a live cable will
also make the metal parts of the tool live and will
cause an electric shock.
The drill is not designed for use with attachments.
n
Do not use near vapors or inflammable liquids.
n
Make sure you have a steady foothold when
n
working on ladders and platforms.
Prior to drilling in walls where electricity, water or
n
gas lines are concealed, use a cable/pipe
detector to locate the lines.
Do not lose this safety information.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
2. Layout and items supplied (Figure 1)
2.1 Layout
1. Scroll chuck
2. Drill depth stop
3. Drill/hammer drill selector switch
4. Locking button
5. ON/OFF switch
6. Speed controller
7. Clockwise/Counter-clockwise switch
8. Additional handle
9. Chuck key
2.2 Items supplied
Open the packaging and take out the equipment
n
with care.
Remove the packaging material and any
n
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
n
Inspect the equipment and accessories for
n
transport damage.
If possible, please keep the packaging until the
n
end of the guarantee period.
IMPORTANT
The equipment and packaging material are not
toys. Do not let children play with plastic bags,
foils or small parts. There is a danger of
swallowing or suffocating!
n
n
n
n
n
3
Th
no
bi
Th
pu
m
m
of
Pl
de
ap
m
bu
4
Se
S
So
ac
W
Th
To
de
Ad
W
Th
ac
m
is
ex
Th
th
Th
as