ST CS 100 Li 20 A Manual De Instrucciones página 162

Whenever the machine is to be handled or
transported you must:
– turn off the motor, wait for the chain to stop
and unplug the machine from the mains;
– apply the protection bar cover;
– only hold the machine using the handles and
position the bar in the opposite direction to
that used during operation.
When using a vehicle to transport the machine,
position it so that it can cause no danger to
persons and fasten it firmly in place.
• Recommendations for first-time users
Before felling or delimbing for the first time, make
sure:
– to have been specifically trained to use this
type of equipment;
– to have carefully read the safety regulations
and user instructions contained in this
manual;
– you practise first on logs on the ground or
attached to trestles, in order to get familiar
with the machine and the most suitable
cutting techniques.
• Handling and correct use of battery-
operated power tools
a) Make sure that the machine is switched
off before inserting the battery. Inserting
a battery in an electric device which is
switched on can cause accidents.
b) Charge battery packs only with the chargers
recommended by the manufacturer. Battery
chargers are generally specific for each
battery type; use with other types can cause
fire risks.
c) Use only batteries specifically designed for
your power tool. The use of other batteries
may cause injuries and fire risks.
d) Keep all unused batteries at a distance
from paper clips, coins, keys, nails, screws
or other small metal objects as contact with
the same can cause short circuits. Short
circuits between battery contacts can lead
to explosion or fires.
e) Batteries in poor condition can cause
liquids to leak. Avoid contact with the liquid.
In the case of accidental contact flush with
water. If the liquid comes into contact with
the eyes, also seek medical advice. Liquid
leaking from the battery may cause skin
irritation or burns.
f) Check that the accumulator is in good
condition and there are no signs of damage.
Do not use the device with a damaged or
worn accumulator.
2.4 BATTERY / BATTERY CHARGER
ATTENTION
The following safety rules complement the
safety rules contained in the battery charger
manual.
• Only use battery chargers recommended by
the manufacturer to recharge batteries. An
inadequate battery charger may cause electric
shock, overheating or corrosive liquid to leak
from the battery.
• Use only batteries specifically designed for
your power tool. The use of other batteries may
cause injuries and fire risks.
• Keep all unused batteries at a distance from
paper clips, coins, keys, nails, screws or other
small metal objects as contact with the same
can cause short circuits. Short circuits between
battery contacts can lead to explosion or fires.
• Never use the battery charger in environments in
the presence of vapours, flammable substances
or on easily flammable surfaces such as paper,
fabric, etc. The battery charger heats up during
recharging and may cause a fire.
• When transporting batteries, make sure the
contacts never come into contact with each
other and never use metal containers to
transport them.
2.5 PROTECTING THE ENVIRONMENT
Safeguarding the environment must be a relevant
and priority aspect of machine use, of benefit to
the community and the environment we live in.
• Avoid being a disturbance to the
neighbourhood. Use this machine at
reasonable times of the day only (not
early morning or late evening when the
noise could cause disturbance).
• A certain amount of chain lubricating oil
is released into the environment when
the machine is running, so only use
biodegradable oils made specifically for this
use. Use of a mineral oil or motor oil causes
serious damage to the environment.
• Comply with local regulations for the
disposal of packaging, deteriorated parts or
any elements with a strong environmental
impact; this waste must not be disposed of
as normal waste, it must be separated and
taken to specified waste disposal centres
where the material will be recycled.
• Comply with local regulations for
the disposal of waste materials
• When the machine is withdrawn from service,
do not dispose of it in the environment,
but take it to a waste disposal facility in
accordance with the local regulations in force.
EN - 5