Publicidad
Idiomas disponibles
Idiomas disponibles
4. BEDIENUNG DES MODELLS S-WIGMA 200D
Front view of the device
Rear view of the device
6
1
4
2
3
CONTROL PANEL VIEW
1
4
5
8
2
Control panel description
1.
Welding current display
2.
Welding current adjustment knob
3.
VRD indicator
Safety function – only for MMA welding: This function allows to reduce the idling voltage to a user-safe
value when the device is ready for welding. After commencing welding, the idling voltage automatically
grows to the nominal value, and after finishing welding it drops back to the safe value again.
4.
VRD gauge ON/OFF switch
5.
MMA method indicator
6.
Lift TIG method indicator
7.
Welding method selection button
8.
ERROR INDICATOR = The indicator lights in the following two situations:
a.
If the machine has malfunctioned and cannot be operated.
b.
If the cutting device has exceeded the standard working time the protection mode is initiated and
the machine will stop functioning. This means that the machine is now being cooled in order to be
able to restore temperature control again after the device has overheated. Therefore the machine
is stopped. During this process, the red warning light on the front panel lights up. In this case it is
not necessary to remove the power plug from the socket. The ventilation system may be left on
in order to enhance the cooling of the machine. When the red light goes dark, this means that
the temperature is now down to the normal level and the unit can be put back into operation.
4.1. CONNECTING LEADS
INSTRUCTIONS FOR CONNECTING LEADS
MMA WELDING MODE
1.
Use the selection button to select MMA welding mode.
2.
Connect the return lead to the socket marked with „+", and tighten the locking nut.
EN
5
Device description
1.
Welding machine control panel
2.
„+" lead output
3.
„–" lead output
4.
Power cable
5.
Welding machine ON / OFF switch
6.
Carry handle
3
6
7
14
Rev. 24.07.2017
3.
Then connect the welding lead to the correct socket, marked with the „–" sign and tighten the locking
nut. WARNING! Polarization of the leads may be different! All polarisation information should be
shown on the packaging supplied by the electrode manufacturer!
4.
Now you can connect the power lead and turn the power on, once the return lead is connected to the
welded element, you can start working.
TIG WELDING MODE
1.
Use the selection button to select Lift TIG welding mode.
2.
Connect the return lead to the socket marked with „+", and tighten the locking nut.
3.
Then connect the TIG welding lead to the socket marked with the „-" sign, connect the TIG welding
control lead and tighten the locking nut. Connect the gas lead directly to the gas canister. Gas flow is
adjusted using the knob on the welding torch.
4.
Now you can connect the power lead and turn the power on, once the return lead is connected to
the welded element, you can start working.
5. S-MULTI 130D MODEL OPERATING INSTRUCTIONS
Front view of the device
Rear view of the device
1
6
7
8
2
9
5
3
4
Inside View
2
3
1
5
4
Control panel view
5
1
4
3
2
6
Rev. 24.07.2017
EN
Device description
1.
Control panel
2.
Welding torch
3.
„+" lead output
4.
„–" lead output
5.
Polarisation change lead
6.
Welding machine ON / OFF
switch
7.
Gas connector
8.
Power cable
9.
Device fan
Device description
1.
Filler wire reel mount
2.
Tension adjustment knob
3/4/5. Wire guide
Control panel description
1.
MIG method parameter change button
2.
VRD lock button
3.
INCHING – upon pressing this button, the
welder starts to feed the wire. The wire will
be fed until the button is released. It is used to
feed the wire, e.g. upon the reel replacement.
4.
Welding method selection button (MMA/ Lift
TIG/ MIG)
5.
LED display (voltage, selected parameters and
welding mode)
6.
Selected parameter adjustment knob
15
Publicidad
