Publicidad
BUstO)0)-)m
=~ n OLOMBINIC
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component,
check the points below. Sometimes the trouble may lie in another component.
Investigate the other components
and electrical
appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or
your dealer to carry out repair work.
Symptom
Cause
Remedy
There is no power.
e@AC cord is unplugged.
ePlug the power cord into a wall socket.
No sound from speakers.
@ Volume is turned all the way down.
e Raise volume setting.
J
e@ Speaker cords are connected
with the vinyl | Strip vinyl insulation from speaker wire tip
@
insulation still on.
before connecting.
S
eFunction
is not set to the desired
listening | eSelect the correct function.
o
source.
Sound from only one speaker.
@One of the speaker cords is disconnected or | eConnect correctly or replace with a new
damaged.
cord.
No reception.
e@ Antenna is not connected.
eConnect the antenna correctly.
e@Wrong radio band.
eSet to the desired radio band.
Noise heard.
eTV ison.
eTurn off the TV.
-
e@ Loop antenna is not positioned properly.
e@ Change the loop antenna position.
s
e Interference
from nearby fluorescent
light, hair | eStop
using
the
device
causing
the
e
dryer or other electrical appliance.
interference.
Sound is distorted, or no stereo | eAntenna is in poor position.
e Change the antenna's position.
sound (during FM broadcast).
e@ Broadcast is weak.
e Use an external antenna (page 10).
e@The MONO button is on.
e@Press the MONO
button (on the remote
control unit (page 14)).
When playback is started, it stops | e Disc is loaded upside down.
e Load the disc correctly with the label side UP.
immediately.
@ Dirt, etc. on the disc.
eClean the disc.
3 | Pauses or stops during playback.
>
=
No sound.
@ Player is in pause mode.
e Press the Pause/Play (I/m) button (on the
a
remote control unit).
oO
With certain discs, loud noise is
produced, or play stops.
Cassette door does not open.
Cassette door does not close.
Tape does not move.
e@ Disc has a bad scratch or warp.
e@ Deck has not stopped.
e@Power was switched off while a tape was
running.
e Cassette is inserted incorrectly.
e Replace the disc.
ePress the STOP (m) button.
e@ Switch on the power again.
e@ Reload the cassette tape correctly.
Cannot record or copy tape.
eErasure prevention tabs are broken off.
@ Dirty head.
e@Apply adhesive tape over the tab holes.
e Clean head (page 48).
Previously
recorded
sounds
remained.
Cassette
Tape
Deck
High-range sounds are over-
emphasize.
e@ Dirty head.
e The cassette tape used is a TYPE II (HIGH/CrO2)
or TYPE IV (Metal) tape.
e@Clean head (page 48).
e Use only TYPE I (Normal) tapes.
Remote
control unit does not
work.
& Others
Timer does not work.
Remote
Control
Unit
e Batteries are dead or no batteries in the remote
control unit.
e@Poor angle or too great a distance from the
remote control sensor window.
eA fluorescent light is shining on the remote
sensor window.
elnsert new batteries.
e Use within 7 meters and within a 30 degree
angle of the remote sensor window (page 6).
eTurn off the light.
e Current time is not set.
e The TIMER button is set to the off position.
e Set current time.
e Set to the on position (page 44).
Abnormal functioning of this unit may be caused by static electricity or other external interference. To restore normal operation, turn
the power off and then on again or unplug the AC power cord and then plug it in again.
50
<ARE7108>
En
Publicidad
