Hitachi Koki NR 90GC2 Instrucciones De Manejo página 8

English
30. The exploded assembly drawing on this handling
instructions should be used only for authorized
service center.
PRECAUTIONS ON USING GAS STRIP NAILER
1. Safe operation through correct usage.
This tool was designed for driving nails into wood and
similar materials. Use it for its intended purpose only.
2. Be careful of ignition and explosions.
This tool must not be used in a
combustible
presence of fl ammable liquids or
gases. This tool produces hot exhaust
gases that may ignite fl ammable
materials and produces sparks. Since sparks may fl y
during nailing, it is dangerous to use this tool near
lacquer, paint, benzine, thinner, gasoline, gas,
adhesives and similar infl ammable substances as they
may ignite or explode. Under no circumstances should
this tool therefore be used in the vicinity of such
infl ammable material.
3. Explosion and fi re hazard.
The fuel cell is an aerosol dispensers
with fl ammable contents.
Pressured container and the propellant
will remain in the fuel cell.
Failure to follow instructions may result
in explosion or fi re.
Keep the power tool, fuel cells and
MAX 50°C
battery away from sunshine and from
(120°F)
temperature exceeding 50°C (120°F).
Fuel cell and/or battery may burst,
releasing fl ammable gas.
Do not pierce or burn the container,
even after use.
Do not incinerate, refi ll, reclaim or
recycle the fuel cell.
Do not spray to a naked fl ame or any
incandescent material.
Keep away from ignition sources – No smoking.
Keep out of the reach of children.
4. Always wear eye protection (protective goggles).
When operating the power tool, always
wear eye protection, and ensure that
surrounding people wear eye protection
too.
The possibility of fragments of the nails
that were not properly hit entering the
eye is a threat to sight. Eye protection can be bought at
any hardware store. Always wear eye protection while
operating this tool. Use either eye protection or a wide
vision mask over prescription glasses.
Employers should always enforce the use of eye
protection equipment.
5. Protect your ears and head.
When engaged in nailing work please wear ear muffl ers
and head protection. Also, depending on condition,
ensure that surrounding people also wear ear muffl ers
and head protection.
6. Use outside or well-ventilated areas.
This tool exhausts carbon monoxide
which are a danger to health when
inhaled.
This tool shall not be used in enclosed
or poorly ventilated areas.
Do not inhale.
8
environment or in
7. Pay attention to those working close to you.
It would be very dangerous if nails that were not properly
driven in should hit other people. Therefore, always pay
attention to the safety of the people around you when
using this tool. Always make sure that nobody's body,
hands or feet are close to the nail outlet.
8. Never point the nail outlet towards people.
Always assume the tool contains
fasteners.
If the nail outlet is pointed towards
people, serious accidents may be
caused if you mistakenly discharge the
tool. When connecting and disconnecting the battery
or fuel cell, during nail loading or similar operations,
be sure the nail outlet is not pointed towards anyone
(including yourself). Even when no nails are loaded at
all, it is dangerous to discharge the tool while pointing
it at someone, so never attempt to do so. No horseplay.
Respect the tool as a working implement.
9. Before using the power tool, check the push lever.
The Push Lever and Chamber operate in conjunction
for this device.
Before using the power tool make sure to check
that the push lever operate properly. Without nails,
fuel cell and battery loaded into the power tool, check
the following.
If abnormal operation occurs, do not use the power tool
until it has been inspected and repaired.
○ Pull the Feeder knob with the device facing upward
and press down the Push lever then confi rm that the
Push lever securely returns to its original position.
The Push lever operation becomes especially
heavy in low temperatures and drive operations
may not function.
○ With pulling back the feeder knob, the push lever
must move smoothly.
○ With pulling back the feeder knob, the trigger must
move smoothly.
Furthermore, with regard to the push lever, please
note that it must never be modifi ed or removed.
10. Use specifi ed nails only.
Never use nails other than those specifi ed and
described in these instructions.
11. Be careful when connecting the battery.
When connecting the battery and loading nails in
order not to fi re the tool by mistake, make sure of the
followings.
○ Do not touch the trigger.
○ Do not allow the fi ring head to contact with any
surface.
○ Keep the fi ring head down.
Strictly observe the above instructions, and always
make sure that no part of the body, hands or legs is
ever in front of the nail outlet.
12. Do not carelessly place your fi nger on the trigger.
Do not place your fi nger on the trigger except when actually
nailing. If you carry this tool or hand it to someone while
having your fi nger on the trigger, you may inadvertently
discharge a nail and thus cause an accident.
13. Press the nail outlet fi rmly against the material to
be nailed.
When driving in nails, press the nail outlet fi rmly against
the material to be nailed. If the outlet is not applied
properly, the nails may rebound.
14. Keep hands and feet away from the fi ring head
when using.
It is very dangerous for a nail to hit the
hands or feet by mistake.