Topcom RC-6405 Airsoft Edition Manual De Usuario página 7

8
• If you press the
PTT
code, the PMR will go back in stand-by mode on the channel with
the CTCSS code.
• If no CTCSS code is detected there is a chance that DCS is
selected by the user. In this case you can scan for the DCS code.
(section 13.10.3)
13.10.3 Scanning for a DCS code
• Press the
00" flashes on the display for the selected radio channel.
• Press the
DCS scan.
Once there is a transmission on the channel, the DCS code (if used) will be detected and
displayed.
If you press the button
PTT
PMR will go back in stand-by mode on the channel with the DCS code.
13.11 Call Tones
A call tone alerts others that you want to start talking.
13.11.1 Setting the Call Tone
The Twintalker RC-6405 has 15 call tones.
• Press the
the current call tone is flashing.
• Press the
another Call Tone.
• Press the
mode.
13.11.2 Sending a call Tone
Press the button briefly. The call tone will be transmitted on the set channel.
6
13.11.3 Call tone reception type
• Press the -button nine times.
7
• Press the -button or
11
1. Tone only
2. Tone + vibration
3. Vibration only
Press the -button to confirm and return to stand-by mode.
12
PTT
button while listening to a found CTCSS
12
-button seven times : "SCAN" and "DCS
7
-button or the -button to start the
11 10
while listening to a found DCS code, the
12
- button 7 eight times, "C" is displayed and
- button or the - button to change to
10
11
- button to confirm and return to stand-by
12
PTT
-button to select the call tone reception type.
10
13.12 Roger Beep On/Off
After the -button is released, the unit will send out a roger beep to confirm that you have
PTT 12
stopped talking.
To set the Roger Beep.
• Press the - button
• Press button
11
Beep (OFF).
• Press the - button
PTT
standby mode.
13.13 Key-Tone On/Off
When a button is pressed, the unit will beep briefly.
To set the key-tone.
• Press button
7
• Press button
11
Tones (OFF).
• Press the - button
PTT
standby mode.
13.14 Dual Channel Monitor function
In stand-by, the PMR is set on one channel with CTCSS/DCS code. The PMR will only receive
signals transmitted on that channel with the CTCSS/DCS code.
Dual Channel Monitor (DCM) allows you to monitor a second channel with CTCSS/DCS code.
• Press the
flash on the display.
• Press the
channel.
• Press the
and go to CTCSS selection. (Press the
again to go to DCS selection)
• Press the
the CTCSS code or DCS code.
• Press the
mode.
• To disable the function select "OFF" when selecting the
DCM channel.
When the Dual Channel Monitor function is activated, the PMR will switch sequentially between
the standby channel + CTCSS/DCS code and the Dual Channel + CTCSS/DCS code.
Twintalker RC-6405
ten times. 'rO' will be displayed.
7
to enable (ON) or button to disable the Roger-
10
to confirm your selection and return to the
12
eleven times. 'tO' will be displayed.
to enable (ON) or button to disable the Key
10
to confirm your selection and return to the.
12
-button twelve times," DCM OFF" will
7
-button or the -button to change the
11 10
-button to confirm the channel selection
7
-button
-button or the -button to change
10
11
-button to confirm and return to stand-by
12
PTT
7