geberit UNIVERSAL Instrucciones De Uso página 17

UNIVERSAL
1
2
3
4
5
o
7
ö
Structure
Machine frame
Toothed rack
Guide bar
Clamping carriage
Tensioning block
Handwheel
Pressure scale
Eccentric
lever
9
Adjustable eccentric lever
10
Clamping plate supporl
11
Locking
lever
12
Clamping screw
13
V-block diam.
50
-
160
14
V-block diam, 200
15
Stop
16
Mirror arm
80 cm
17
Welding mirror
18
Electric plane
19
Hand plane
20
Welding accessories for diam.
200 - 315 incl. ring welding
mirror, electrical
plane, tension
clamp, electrical
switch box
etc,
Welding mirror KSS
160:
23OV
/
630 W
Welding mirror
KSS
200:
23OV
/
630 W
Ring welding mirror
(3'15)
23OV
/
1300 W
Technical
spec¡f ¡cat¡ons
Lenoth:
width:
40
cm
Heiqht:
23 cm
Weiqht
(machine):
aporox. 60
kq
Used for: PE
pipes
and
fittings with diameter
50-315
mm
7
Generate
the required welding pressure to deter-
mine
whether the welding part
is
secured firmly
enough. lf necessary, tighten with the adjustable
knurled nut
on
the eccentric lever
9.
I
For
face end planing, the welding parts
are
pres-
sed lightly against the plane discs (use electric
plane
at
stage
1).
Check by moving the cut surfa-
ces
together.
I
With the electric plane
18,
you can plane
just
one
side by swinging out the
stop
15.
10
Swing the welding
mirror 17 (at
welding tempera-
ture) between the
two parts or insert it with the mir-
ror
stand.
11 Press
the workpieces lightly against the welding
mirror 17 so that the cut sudaces start
to
melt.
Observe
the melting process carefully.
When the
welding bead
is
the
size
of
a
match
head,
the mir-
ror can be removed
12
Carefully press the welding parts together with the
required
welding
pressure,
see pressure scale
7.
Tighten the locking handlel
l
to maintain the pres-
sure until the weld
has
cooled. After cooling (about
30 seconds), release
the locking handle again (by
gently turning the handwheel clockwise).
230V /
550 W
Electric plane
(200):
23OV / 550 W Subiect to desiqn alterations without notice.
Electric plane
(315):
230V
/
550 W
Electric olane
(160):
Setup and operat¡on
I
Push the welding mirror arm 16 and the electric
plane
18
onto the guide
bar
3 in
the
base element.
Fix the bar
in place.
2
Attach the clamping plates
of
the required dimen-
sions
to the protruding dovetail head of
the clam-
ping screw
12 at the
face ends of the work tops
4
and
5. Use
the cam
on
the
V-block
13
to accura-
tely centre the right-hand clamping plate with
the
larger recess,
A
Note:
The
clamping plates must
fit
securely.
Check
for correct positioning.
When
the clamping plates
are
correctly positioned
tighten them with the eccentric lever
8.
3
Move
in
the
V-blocks
13
and fix.
4
For
diam. 200 remove the
V-block
13 and move
in
V-block
14.
5
lnsert the welding parts into the clamping plates
and V-blocks so
that the
area
to
be
welded is
1 cm
from the clamping
plate. The
welding parts should
rest
on the
V-block
13 as
far away from the clam-
ping plates as possible. ln bends it must
be on
the
straight section, Clamp down the welding parts by
closing the clamping plates using the eccentric
lever
9.
6
The right-hand clamping plate can be moved to the
side by
releasing
the eccentric
lever
I
if
the wel-
ding parts
do not match axially (e.9. a bend or
bend segments).
-17
-
TGEBERIT