HIKOKI C 6SS Instrucciones De Manejo página 4

English
13. For model C6SS, the saw blades range should be from
165 mm to 160 mm.
For model C7SS, the saw blades range should be from
190 mm to 185 mm.
14. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or maintenance.
15. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
16. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
17. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
18. Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
(Fig.1)
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
19. Should lever (A) remain loosened, it will create a very
hazardous situation. Always thoroughly clamp it. (Fig.2)
20. It is very hazardous to allow wing bolt to remain loosened.
Always thoroughly clamp it. (Fig.3)
21. Prior to cutting operation, make sure the material you
are going to cut. If the material to be cut is expected to
generate harmful / toxic dusts, make sure the dust bag
or appropriate dust extraction system is connected with
dust outlet tightly.
Wear the dust mask additionally, if available.
○ Before starting to saw, confi rm that the saw blade has
attained full-speed revolution.
○ Should the saw blade stop or make an abnormal
noise while operating, promptly turn OFF the switch.
○ Always take care in preventing the power cord from
coming near to the revolving saw blade.
○ Using the circular saw with the saw blade facing
upwards or sideways is very hazardous. Such
uncommon applications should be avoided.
○ When cutting materials, always wear protective
glasses.
○ When fi nished with a job, pull out the plug from the
receptacle.
22. After having attached the saw blade, reconfi rm that the
lock lever is fi rmly secured in the prescribed position.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
C6SS / C7SS : Circular Saw
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
Always wear hearing protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
Cutting depth
P
Power Input
n
No-Lode speed
0
Weight (without cord)
kg
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1), the package contains
the accessories listed in the below.
○ Saw Blade (mounted on tool) ......................................1
(
Dia. 165 mm ................................ C6SS
Dia. 190 mm ................................ C7SS
○ Hex. Bar wrench .........................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
The specifi cations of this machine are listed in the Table on
page 99.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Adjusting the cutting depth
Adjusting the angle of inclination
Regulating the guide (Optional
accessory)
Cutting line
4
)
Figure Page
2 100
3 100
4 100
5 100