Descargar Imprimir esta página

Denon AVR-1603 Instrucciones De Operación página 10

Ocultar thumbs Ver también para AVR-1603:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 111
, _
_
switch
on the main unit to turn on the power
{Main
unit)
Press the SYSTEM SETUP button to enter the setting
,++,..+.
,.+:, ]
NOTE: Please
make
sure the "AUDIO" position
of the slide switch
on the
remote
control unit
Use the
_
(left) and _
{right) buttons
to select your subwoofer
setting
(Initia0
(left) button
(right) button
Press the ENTER or _
(down) button to enter the settings
and switch to the
SUBWQQFER
MODE setting
• Parameters
Large ......
Select
this
when
using
speakers
that
can fully
reproduce
low
sounds
of below
80 Hz
Small
......
Select
this
when
using
speakers
that
cannot
reproduce
low
sounds
of below
80 Hz with
sufficient
volume¸
When
this setting
is selected,
low
frequencies
of below
80 Nz are assEgned
to the subwoofer
None
......
Select
this
when
no speakers
are installed¸
Yes/No
Select
"Yes"
when
a subwoofer
is installed,
"No"
when
it's not installed¸
_
._.
Press
the
ENTER
or _
(down)
button
to switch
to the
speaker
configuration
set up
NOTE:
Press the SYSTEM SETUP button again to finish system set up System set up can be finished at any time
The
changes to the settings
made up to that point are entered
,
(left) button
(right) button
NOTE:
Select "Large"
or "SmaW' not according to the physical size of the speaker, but according to the bass reproduction
capacity at 80 Hz If you cannot determine
the best setting,
try comparing
the sound when set to "Small"
and
when set to "Large",
at a level that will not damage the speakers
Caution:
In case the subwoofer
is not used, be sure to set "Subwoofer
= No", or the bass sound of front channel is divided
to subwoofer
channel and not reproduced
in some mode
Press the ENTER or _
(down) button to switch to the center speaker setting
Use the
_
(left) and _
(right) buttons
to select the Subwoofer
mode
(Initial)
r
1
5 ':S+,.+ H OE:+Ei-K:+RH
_
_
(left) button
(right) button
Press the ENTER or _
(down) button to enter the setting and switch
to the
Crossover
Frequency setting
_
_
_
Use the (_ (left) and _) (r,ght) buttons to selectyour centerspeaker type
(In,t,a,)
_
(_
_._
r:2 +:::EI.++._:.:+4:
::::q,++.:++..L] ¢_
(_4_
{left) button
{right) betton
(_
Press the ENTER or _
(down) button to switch to the surround speaker setting
NOTE:
• When
"Small"
has been selected
for the front speakers,
"Large"
cannot be selected for the center speaker
Use the
_
(left) and _
{right) buttons
to select the Crossover Frequency
(Initial)
r
,,,+.+-1
(left) button
(right) button
Press the ENTER or _
(down) button to enter the setting and switch
to the
SPEAKER DISTANCE setting
,ca-,
NOTE:
Use the
_
(left) and _
(right) buttons to select your surround speaker type
(Initial)
r:!!: "++-' -++-1
(left) button
(right) button
Press
the ENTER or _
(down) button
to switch
to the subwoofer
setting
• When
"Small"
has been selected for the front speakers, "Large"
cannot be selected for the surround
speakers
10

Publicidad

loading