46
SPECI FIC£_iTIONS
Before
calling
for
service
(conf.)
Problem
Possible
Causes
Solutions
Steam does not
. Water level error.
. Unplug
dryer
and call for service.
generate
but no error
code is shown
Garments
still
. Too many or too different
types of garments
. Small loads of 1 to 5 items work
best.
wrinkled
after
in dryer.
. Load fewer garments.
Load similar-type
garments.
Steam Fresh
TM
There are no creases
. The function
of this cycle is to remove
. Use an iron to make creases.
left on garment
after
wrinkles
from fabric.
Steam Fresh
TM
Garments
have
.This is normal.
. Depends
on individual
moisture
level in skin.
static after
Reduce Static
Garments
are too
. Correct
drying
options
not selected.
. Select load weight
manually
before starting
Reduce Static option.
clamp or too dry after
Reduce Static
Garments
are not
. Number of garments
or load size not properly
. Select the correct
number
or garments
or load size before starting
the cycle.
uniformly
clamp after
selected at the beginning
of the cycle.
Easy Iron
Water drips from door
. This is normal.
. Condensation
will normally
form on the inside of the dryer
door during
steam
during
Steam Cycle
operation.
Some condensation
may drip out the bottom
of the door.
Steam is not visible
. This is normal.
. Steam vapor is difficult
to see when
the door is closed. However,
condensation
during
Steam Cycle
will normally
form on the inside
of the dryer door if the steam system is
operating
normally.
Drum does not turn
. This is normal.
. The drum
is turned
off so that the steam vapor remains
in the drum.The
drum
during
Steam Cycle
will normally
turn for about
2 seconds
once a minute.
Cannot
see steam
• This is normal.
• Steam is released at different
stages of the cycle for each option.
vapor at the
beginning
of cycle
The display
shows
. More Time button
pressed.
. This display
indicates
that the steam option
has been set for a"Load
Bulky
Load Bulky items
items"item
such as a comforter.
Press the LESS TIME button
to reduce the indicated
load size.
Odors remain
in
. Steam Fresh
TM
did not remove
odor
. Fabrics containing
strong
odors should
be washed
in a normal
cycle.
clothing
after
completely.
Steam Fresh
TM
. Lint filter is almost
clogged
or full.
. Pause the drying
cycle and clean the lint filter.
. Install a shorter
or straighter
duct
run. See the Installation
Instructions.
CHECK FILTER light
is on during
the
drying
cycle
Flow Sense
TM
indicator
shows four
bars during
the drying
cycle
. Ductwork
is too long or has too many turns/
restrictions.
. Significant
blockage
of the ductwork
due to
lint buildup
or debris.
. The appliance
has detected
a restriction
in
the external
dryer venting.
. Ductwork
should
be checked/cleaned
soon.
Dryer can be used in this condition,
but drying
times may be longer.
TM
. If exhaust
restrictions
are sensed by the FLOW SENSE
system, the indicator
will remain
on for two hours after the end of the cycle. Opening
the door or
pressing
the POWER button
will turn off the display.
SPECIFICATIONS
Description
Steam Dryer
Electrical
Requirements
_
Please refer to the rating
label regarding
detailed
information.
Gas Requirements
_
NG: 4-10.5 inches WC
LP: 8-13 inches WC (Gas Models
only)
Dimensions
29"(W)
x 32.1 "(D) x 40.8"(H)
x 59"(D with door open)
73.6 cm (W) x 81.4 cm (D) x 103.6 cm (H) x 151.8 cm (D with door open)
Net Weight
Gas : 161.21bs(73.1 kg), Electrical
: 155.41bs(70.Skg)
Drying
Capacity
- Steam Cycle
IEC 9.0 cu.ft(81b/3.6kg)