Publicidad
Idiomas disponibles
Idiomas disponibles
Assemble Rear Wheels
Align the axle of the rear wheel with the rear wheel mount, and then insert to assemble the rear wheel
that wheels are securely attached by pulling on wheel assemblies.
To disassemble rear wheel, detach rear wheel from rear wheel mount
- 1
6
Assemble Armbar
Align the armbar end slider with matching fixing slot, and then insert to lock.
To disassemble armbar, press armbar release button
The completely assembled stroller is shown as
9
Stroller Operation
Adjust Backrest
Recline Backrest
Pull the backrest backwards, while pressing the button in the center of the angle adjuster.
Raise Backrest
Push the backrest forwards, while pulling the webbing at the end of the angle adjuster.
!
Make sure the recline is set properly for use.
Use Buckle
Release Buckle
12
Press the center button to release the buckle.
Lock Buckle
Match the waist belt buckle with the shoulder buckle
A "click" sound means the buckle is locked completely.
!
To avoid serious injury from falling or sliding out, always secure your child with harness.
!
Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
!
Do not cross the shoulder belts. This will cause pressure on child's neck.
Use Shoulder & Waist Harnesses
!
In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
- 1
14
Shoulder harness anchor A
- 2
14
Shoulder harness anchor B
- 3
14
Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder
harness anchor B and the lowest shoulder slots.
To adjust the position of the shoulder harness anchor, turn the anchor to be level with the side facing forward.
11
5
- 2
6
while pressing the release button.
7
- 1
- 2
8
, and then pull up the armbar.
8
10
11
- 1
- 2
13
, and click into the center buckle.
13
- 3
13
Thread it through the shoulder harness slot from back to front.
child's shoulder height.
. Check
Use slide adjuster to change the harness length.
Press the button
Adjust Calf Support
The calf support has 2 positions.
Raise Calf Support
To raise the calf support, just push it upwards. A "click" sound means the calf is locked completely.
Lower Calf Support
Press the adjustment buttons on both sides of the calf support
- 2
18
Use Front Swivel Lock
Push down the front swivel locks to maintain the moving direction.
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
To lock wheels, step the brake lever downwards.
To release wheels, just lift the brake lever upwards.
Tip
Always apply brake when stroller is in stopped position.
Use Hood
The hood can be opened or folded, pull it toward front or back.
The hood can be opened completely to protect your child from the sun uttermostly, just unzip the hook
and then pull the hood toward front.
There is a window on the hood, through which you can view your baby.
Roll up the backward panel and stick the hook and loop fastener, then you can view your baby.
!
Total Maximum Weight of hood storage pocket MUST not exceed 0.5 kg.
Fold Stroller
!
Please fold the hood before folding the stroller.
Pull the folding webbing upward, the frame will automatically fold backward.
The storage latch will automatically hook onto the storage mount, then the stroller is folded and locked
- 3
completely.
23
15
Rethread it through the slot that is closest to
16
- 1
17
- 2
17
, while pulling the waist harness to proper length.
18
20
21
- 3
17
- 1
, and rotate the calf support downwards.
19
- 1
,
22
- 2
22
- 2
23
12
Publicidad
