Martin Yale Intimus 315SC2 Instrucciones De Uso página 6

Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung
CONTROLS:
7 = Control display (Fig. 1)
"Oil cutters"
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on
the reverse button (4) (see description in
"CUTTER MAINTENANCE").
8 = Control display (Fig. 1)
"Waste bin moved out" /
"Electrical fault"
a) "Waste bin moved out"
Is lit when the waste bin is moved out.
The machine is automatically switched
off and cannot be started as long as the
waste bin is not pushed in.
b) "Electrical fault"
Flashes if there is an electrical fault in
the monitoring sensor system for the
status "Waste bin not pushed in". The
machine switches off. Please contact
your dealer.
9 = Control display (Fig. 1)
"Motor overload" /
"Electrical fault"
To fi nd out what to do see the relevant
description under the "MALFUNCTION"
section.
a) "Motor protection"
Comes on when the motor has been
overloaded and has switched off. The
machine cannot be started while the
motor is cooling down.
b) "Electrical fault"
Flashes when there is an electrical fault
inside the control board. At the same
time the function button (2) LED display
fl ashes. The machine switches off.
Please contact your dealer.
10 = Control display not occupied
11 = Control display
"Waste bin full" (Fig. 1)
Is lit if the waste bin is full and must be
emptied. The cutting unit for shredding
paper switches off.
Note: The cutting unit for shredding CDs/
DVDs can continue to be used.
6
7
8
2
fi g. 1
OPERATION
12 = Paper feed slot (Fig. 3)
13 = CD/DVD feed slot (Fig. 3)
14 = Waste bin (Fig. 4)
15 = Shredder (Fig. 4)
16 = Frame (Fig. 6)
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to
"Ready":
- Press the function button (2) briefl y.
- The function button (2) LED display
on for "Ready".
- The machine can be loaded.
MATERIAL FEED:
Feed paper into the cutting mechanism through
the paper feed slot (12) (fi g. 3).
Feed data carriers (CD, DVD or credit card)
into the cutting mechanism individually into the
separate CD/DVD feed slot (13) (fi g. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
When shredding papers, do not shred
CD/DVD at the same time, and vice
versa!
Note: For shredding transparent fi lms, the
machine must be manually switched to forwards
running (press and hold the forwards button (3)
for approx. 2 secs.).
By briefl y pressing the function button (2) (Stop
function), the shredding process can be stopped
at any time. To continue, press and hold the
forwards button (3) for approx. 2 secs.
If the machine is not used for a period of approx.
5 mins., it automatically switches off.
Never feed the shredder with a
quantity of material exceeding the
maximum indicated.
TECHNICAL DATA section!
Should the
overloaded, follow the instructions under
"MATERIAL JAM IN MACHINE" under
"MALFUNCTIONS".
3
9
10
12
11
13
4
fi g. 3
EMPTYING THE WASTE BIN (Fig. 4):
If the waste bin is full (14), the machine switches
off. The control display
Proceed as follows:
- Move waste bin out. The control display
- Push the emptied waste bin (14) into the frame
comes
- If the control display
Note: The machine only works when the waste
bin is pushed in!
DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure
a continual, effective destruction of the data
carriers, the current load level of the motor is
displayed during the shredding process by a
coloured, diffuse light in the feed slot as follows:
Green light:
Yellow light:
Red light:
Refer to the
machine become
5
6
(11) comes on.
(8) comes on. If there is still material in one of
the feed slots, the control display
comes on. The control display
out.
(16) under the shredder (15) again as far as it
will go, as shown. The control display
goes out.
(6) comes on, press
the forward button (3) briefl y. The remaining
material in the feed slot is shredded and the
display goes out.
load < 50%
load 50 - 75%
load 75 - 100%
15
14
fi g. 4
(6) also
(11) goes
(8)
16