HIKOKI C1805DA Instrucciones De Manejo página 16

English
– Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
– Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
– If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Inclined cutting using the guide
(+45° direction)
Fine tuning of parallelism
Fine tuning of perpendicularity
Fine tuning of guide piece position
Adjusting the cutting depth
Switch operation
About the mode select function*
Using the LED light
Attaching the guide
Attaching the fluorine plate (sold
separately)
Attaching the dust collection adapter
(sold separately)
Attaching the hook* 2 (sold separately)
Removing and inserting the battery
Charging
Figure Page
9 3
10 3
11 3
12 4
13 4
14 4
1 15 4
16 4
17 5
18 5
19 5
20 5
21 6
22 6
Action
Remaining battery indicator
Cutting at right angles
Inclined cutting (+45° direction)
Connecting with cleaner (sold
separately)
Dismounting the saw blade
Mounting the saw blade
Selecting accessories
*1 About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
efficient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it
automatically returns to Silent mode.
In Power mode, no change is made to Silent mode even
when the load decreases.
Mode
Power
Silent
NOTE
○ The mode will only change after a battery is installed
and the switch is pulled once.
○ The current mode will be maintained even if the switch
is on/off, or the battery is removed/reinserted.
*2 Attaching the Hook
The hook can be used to hang up the unit temporarily
during operations (Fig. 20).
CAUTION
○ The hook should never be used to hang the unit on your
person.
○ When using the hook, check to make sure that the main
unit will not slip and fall, or become unstable by the
wind, etc.
○ Never hang the unit from your belt or trousers as this
could cause accidents.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. If any of the safeguard
functions are triggered during operation, the LED light will
blink as described in Table 3.
When any of the safeguard functions are triggered,
immediately remove your finger from the switch and follow
the instructions described under corrective action.
16
Figure Page
23 6
24 6
25 7
26 7
27 8
28 8
― 264
No-load speed
6000 min- 1
3000 min- 1