Preparatory work
Getting to know the appliance
Fig.
:
Handle;
OFF/MIN/MAX switch;
1
1
2
Dust bin release catch;
4
Brush roller;
Handle release catch;
7
8
able battery compartment cover;
battery compartment release catch;
release catch;
Charging socket;
12
Wall mount;
Rechargeable battery
14
15
Unpacking and assembling
Check that the unpackaged contents are complete.
1
If you notice any transport damage or if anything is
missing, contact your dealer immediately.
handle (Fig.
/
) vertically over the upper installa-
1
1
tion opening on the appliance body (Fig.
process, make sure that the cable does not become
trapped between the handle and the appliance body.
NOTE:
If you wish to remove the handle again, push the
handle release catch (Fig.
pointed object, and pull the handle from the
appliance body.
Insert the handle into the upper installation open-
3
ing on the appliance body so that you feel and hear
it click into place (Fig.
3
body to the floor nozzle so that you hear and feel the
floor nozzle release catch click into place (Fig.
NOTE:
If you wish to remove the floor nozzle again at a
later time, push in the floor nozzle release catch
(Fig.
/
), thus releasing it. Then pull the appli-
1
11
ance body and the floor nozzle apart (Fig.
NOTE:
To set the assembled appliance down, set it down
on the floor nozzle and tilt the appliance body
forwards so that the stop catch on the floor nozzle
clicks into place (Fig.
5
the wall mount (Fig.
7
or store it.
Push the rechargeable battery compartment re-
5
lease catch and remove the rechargeable battery
compartment cover (Fig.
able battery into the rechargeable battery compart-
ment so that the contact surfaces are facing down-
wards (Fig.
).
Now push the rechargeable battery
9
7
into the rechargeable battery compartment so that it
audibly clicks into place (Fig.
chargeable battery compartment cover and close it
so that it audibly clicks into place (Fig.
LED;
3
Dust bin;
Floor nozzle;
5
6
Recharge-
9
Rechargeable
10
Floor nozzle
11
Mains adapter;
13
Turn the
2
). In the
2
1
/
) with a stable,
8
).
Connect the appliance
4
4
).
).
6
). Connect the appliance to
) when you wish to charge
).
Insert the recharge-
8
6
).
Re-insert the re-
10
8
).
11
EN
Charging the rechargeable battery
!
WARNING!
Risk of fire or explosion! Only use the mains adapt-
er included in the scope of supply to charge the
rechargeable battery.
Connect the mains adapter cable to the charg-
1
ing socket on the appliance (Fig.
mains adapter to a socket (Fig.
up constantly in red to indicate the charging pro-
cess (Fig.
).
After a maximum of 4 hours, the LED
14
3
switches to green. ➔ The rechargeable battery is then
charged.
Disconnect the mains adapter from the
4
socket (to save electricity) and disconnect the mains
adapter cable from the appliance.
Installing the wall mount
Connect the handle of the appliance to the wall
1
mount.
Place the appliance against the wall, to-
2
gether with the wall mount, so that the floor nozzle
rests flat on the floor (Fig.
for the drilled holes with a pencil.
Drill the holes.
4
5
the handle and screw it to the wall with suitable fas-
tening accessories.
6
Switching the appliance on/off
NOTE:
When the LED flashes red, the rechargeable bat-
tery charge is low and the appliance will switch off
within 20 seconds. Fully charge the rechargeable
battery to use the appliance again > "Charging
the rechargeable battery" on page 17.
CAUTION!
Make sure that the surface can withstand the ro-
tating brush without becoming damaged.
▶
To switch on the appliance, push the OFF/MIN/MAX
switch one position down (Fig.
ance vacuums at low suction power and the brush
on the floor nozzle rotates. The LED lights up green.
▶
For full suction power, push the OFF/MIN/MAX
switch one position further down (Fig.
▶
To switch off the appliance, push the OFF/MIN/
MAX switch all the way up (Fig.
ance switches off. The LED goes out.
12
).
Connect the
2
). ➔ The LED lights
13
).
Mark the positions
7
3
Remove the wall mount from
Insert the hole covers.
/I). ➔ The appli-
15
/II).
15
/O). ➔ The appli-
15
17