Black and Decker NST2018 Manual De Instrucciones página 2

CHARGING THE B ATTERY
1. This manual contains important safety and operating instructions.
2. Before using b attery charger, read allinstructions and cautionary markings on(1)battery charger, (2)
battery, and(3) product using battery.
3. z_CAUTION: Toreduce the risk ofinury, c harge only Black &Decker Power Packs.
Other types of
batteries may burst causing persona injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock,
or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed extension
cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L). If
the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for
outdoor use can also be used for indoor work. The letters "W' or "WA' on the cord jacket indicate
that the cord is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and
to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater
the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more
than one extension to make up the total length, be sure each extension contains at least the
minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS
NAMEPLATE RATING AMPS - 0 - 10.0
Total Extension Cord Length (fl) 25 50 75 100 125 150
18 18 16 16 14 14
Wire Gauge
9. Use only the supplied charger when charging your unit. The use of any other charger could
damage the battery or create a hazardous condition.
10. Do not attempt to open the charger or the unit. There are no customer serviceable parts inside. Return to
any authorized Black & Decker service center.
11. DO NOT incinerate battery packs even if they are severely damaged or completely worn out.
12. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery
cells may occur under extreme usage, charging or temperature conditions. This does not indicate a
failure. However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of I 0 minutes and seek
immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.
SAVETHESEINSTRUCTIONS
• Slowly swing trimmer side-to-side as shown in Figure 9.
• Toconvert for maintenance edging, turn off the tool. (SeeFigure 1O)Holding the trimmer with one hand by the
auxiliary handle, grasp the collar and push in direction of arrow and rotate the trimmer head until it stops, (half
turn), release your hand, (rotate clockwise when viewed from the switch end). The tool is locked in the edger
position.
Rotatethe wire edge guide forward and clown into place before edging, as shown in Figure 1 I.
• Tooperate as a maintenance edger, position trimmer above sidewalk as shown in Figure 12.
• Return to trimming position by turning the tool off, push in direction of arrow and rotating the trimmer head
counter clockwise until it stops.When using file tool in file trimmer mode you may choose to fold file wire edge
guide up out of the way.
LINE FEEDING
Your trimmer uses .065" (1.65mm) diameter nylon line to cut ,qrassand weeds quickly and easily. In time, the tip of
file nylon line will become worn and file auto feed mechanism-will automaticallyfeed and trim a fresh length oFline.
The cutting line will wear faster if the cutting is done along sidewalks or other abrasive surfaces or heavier weeds
are being cut. The automatic feed mechanism senseswhen more cutting line is needed and feeds and trims file
correct lenqth of line whenever it is required. Youdon't even have to think about it. Do not bump unit on ground in
attempt to feed line or for any other purpose.
REPLACINGSPOOL/CLEARING JAMS AND TANGLED LINES
Fromtime to time, especially when cutting thick or stalky weeds, the line feeding hub may become dogged with sap
or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below.
• Turnoff the trimmer and remove file battery.
• Pressthe release tabs on the line spool cover, as shown in Figure 13 and remove the cover by pulling it straight off.
• Liftthe spool of nylon line out of the hub and clear any broken line or cutting debris Fromfile spool area.
• In case of jams and tangled line unwrap about one foot (30cm) of line to ensure that it is undamaged. If it is OK
rewind it and insert the line end through the eyelet in the spool hub, as shown in Figure 14. Pullthe line through the
hole to maintain tension while placing file spool clown into the hub with the notched side exposed, as shown in
Figure 15.
• Pressfile spool clown GENTLYand rotate it until you feel itdrop into place. (When in place, the spool will turn a
few degrees left and right freely.)
• Snap the spool cover back on, insert file battery and turn the tool on. In a few seconds or lessyou'll hear tile nylon
line being cut automatically to the proper bngth.
REWINDING SPOOL FROM BULK LINE (USEONLY .065" DIAMETER LINE)
Bulk line for your trimmer/edger is avai]abb at extra cost from your local dealer or Black & Decker ServiceCenter.
To install bulk line, follow file steps below.
• Turnoff the trimmer and remove tile battery.
• Pressfile release tabs on the line spool cover, as shown in Figure 13 and remove the cover by pulling it straight off.
• Remove the spool from tile tool and remove and discard all line on tile spool.
• Insertone end of the bulk line into the hole in file spool shown in Figure 16 about 1/2" (12ram).
• Hold the line in the hole and pull the rest of the line through file slot in file spool, shown in Figure 16.
• Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on spool in Figure 16 until it is
near]y full. (The spool holds 50 ft. (15.2m) of line and bulk line is sold in 50 Footsections.)
• Insertthe line end through file eyelet in file spool hub, as shown in Figure 14. Pulltile line through the hob to
maintain tension while placing the spool clown into the hub with the notched sicle exposed, as shown in Figure 15.
• Pressthe spool down GENTLYand rotate it until you feel itdrop into place. (When in place, the spool will turn a
few degrees left and right freely.)
• Snap the spool cover back on, insert tile battery and turn the tool on. In a few seconds or lessyou'll hear tile nylon
line being cut automatically to the proper length.
TROUBLESHOOTING GUIDE
Problem PossibleCause Solution
1. Unit won't run. A. Battery not charged. A. Charge for at least 12 hours.
B. Battery not properly attached. B. Remove and reattach
battery/handle.
2. Line won't feed. A. Line tangled in spool. A. Unwrap 24" of line and rewind.
3. Line fails to cut off. A. Line cutter in guard is A. Return to service center for
damaged or missing, replacement!repair.
B. Line extends past guard. B. Rewind or trim line to line
cutter.
CHARGING THE POWER PACK
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLYCHARGED AT THE FACTORY.BEFOREAITEMPTING
TO CHARGETHEM, THOROUGHLY READALLOF THE SAFETYINSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge by means of an
engine generator or DC power source. Use only 120V AC.
2. Slide the charger onto the power pack as shown in Figure 6 & 7 and let the power pack charge initially
for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to
6 hours.
3. Unplug charger, and remove the power pack. Place the power pack in the unit and be certain that it is
inserted fully into the battery cavity until it "clicks" into place.
NOTE: To remove the power pack from the unit, press down on the release button on the back of the
pack (Figure 8) and slide out.
IMPORTANT CHARGING NOTES
1. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the power pack is
run-down completely, it may take up to 6 hours to become fully charged. Your power pack was sent from
the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C).
This is important andwill prevent serious damage to the power pack. Longest life and best performance
can be obtained if power pack is charged when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm to touch. This is a normal condition and does
not indicate a problem.
4. If the power pack does not charge properly--(1 ) Check current at receptacle by plugging in a lamp or other
unit. (2) Check to see if receptacle is connected to a light switch which turns power of Fwhenyou turn out
the lights. (3) Move charger and power pack to a surrounding air temperature of 40 F (+4.5 C) to 105 F
+40.5 C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send
the power pack and charger to your oca Back & Decker service center. See Too s Eectric in ye ow pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs which were
easily clone previously. DO NOT CONTINUE using unit with its power pack in a depleted condition.
6. The power pack will reach optimum performance after being cycled 5 times during normal usage. There is
no need to run the batteries down completely before recharging. Normal usage is the best method of
discharging and recharging the power pack.
LEAVING THE BATTERYPACK IN THE CHARGER
The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not been
kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly
lose its charge if left in a charger that is not plugged into an appropriate AC source.
CLEANING
• Useonly mild soap and damp cloth to clean tile tool. Never letany liquid get inside the tool; never immerse any
part of the tool into a liquid.
• Z_ WARNING: Remove or disconnect battery before servicing, cleaning or removing material from tile
gardening appliance.
ACCESSORIES
• Recommendedaccessories for use with your tool are available from your local dealer or authorized service center.
If you need assistance regarding accessories, please call: 1-800-54-HOW-TO.
• Use Black & Decker replacement spool No. AF-IO0.
• Reload nylon line (either bulk or prewrapped replacement spool) as shown in this manual.
• USEONLY .065" (1.65mm) DIAMETERNYLON MONOFILAMENT LINE.
Heavier line will overload the motor, cause overheating and will impair tile automatic feed. This line is available at
your local dealer or authorized service center.
• Do not use fishing line or other lines that are not recommended.
• Z_ WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
THE RBRC
TM
SEAL (_
The RBRC
TM
(Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium
battery (or battery pack) indicates that the costs to recycle the battery (or battery pack)
at the end of its useful life have already been paicl by Black & Decker. In some areas, it
is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC
program provides an environmentally conscious alternative.
RBRCin cooperation with Black & Decker and other battery users, has established programs in the United
States and Canada to facilitate the collection of spent nickel-cadmium batteries. Help protect our environment
and conserve natural resources by returning the spent nickel-cadmium battery to an authorized
Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling
center for information on where to drop off the spent battery, or call 1-800-8-BATrERY.
Before assembling your Cordless String Trimmer, check that you have received the following in the shipping
carton. See Figure I.
A. Guard. C. Nicad Battery Pack. E. Auxiliary Handle.
B. Charger. (NOT SHOWN) D. Trimmer/Edger.
ATTACHING THE GUARD
• Z_ WARNING: NEVER OPERATETOOL WITHOUT GUARD FIRMLYIN PLACE.
THE GUARD MUST ALWAYS BEON THE TOOL TO PROTECTTHE USER.
• Assemble the guard as shown in Figure 2, over the lug on the motor housing, then slide guard forward to
lock on the lug. Then with a phillips screw driver, screw the preassembled screws in the guard into the motor
housing. Figure 3.
AUXILIARY HANDLE ADJUSTMENT
• For maximum comfort and control, ad ust the auxiliary handle to suit your heiqht (Figure 4A). Shorter users
adjust handle to a lower position (away Fromyou) and taller users, adjust hanc]le to an upper position
(towards you). The handle should be adjusted so that your front arm is straight as shown in Figure 9.
HEIGHT ADJUSTMENT
• The overall height of the trimmer can be adjusted by loosening the lock collar and rotating it opposite to the
arrow shown in Figure 4B. The tubes can then be extended shorter or longer. When the desired height is
achieved tighten the collar by rotating in the direction shown in Figure 4B.
• Z_ CAUTION: ALWAYSWEAR EYEPROTECTION.
• _ CAUTION: Inspectarea to be trimmed and remove any wire, cord, or string-like objects which could become
entangled in the rotating line or spool. Beparticularly careful to avoid any wire which might be bent
outwardly into the path of thetool, suchas barbs at tile base of a chain link fence.
OPERATETHETRIMMER/EDGER
• To turn trimmer on, pull the lock out button, shown in Figure 5, back and, then squeeze tile trigger switch. To turn
the tool off, release the trigger.
SERVICEINFORMATION
IMPORTANT: To assure product SAFETY and RELIABILITY, r epairs, maintenance and adjustment should be
performed by Black & Decker service centers or other qualified service organizations, always using identical
replacement parts.
Black & Decker offers a full network of company-owned and authorized service locations throughout North
America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with
efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker
location nearest you.
To Findyour local service location, refer to the yellow page directory under "Tools--Electric"
or call: 1-800-54-HOW-TO.
FUlLTWO-YEAR HOME USEWARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or
workmanship. The defective product will be replaced or repaired at no charge in either of two ways:
The First,which will result in exchanges only, is to return the product to the retailer Fromwhom it was
purchased (provided that the store is a participating retailer). Returns should be made within the time period
of the retailer s policy for exchanges (usually 30 to 90 clays after the sale). Proof of purchase may be
required. Please check with the retailer for their specific return policy regarding returns that are beyond the
time setfor exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized service
center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned
and authorized service centers are listed under "Tools-Ebctric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have
other rights which vary From state to state. Should you have any questions, contact the manager of your
nearest Black & Decker Service Center.
This tool is not intended for commercial use.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See 'Tools-Electric'
- Yellow Pages -
for Service & Sales