Publicidad
Idiomas disponibles
Idiomas disponibles
TIMER
SHIFT
The unit can be turned on at a specified
time every day with the
built-in
timer.
Preparation
Make sure the clock is set correctly.
1 Press one of the function
buttons
to select
a
source.
@
If TUNER/BAND
is pressed,
the band cannot be selected
in
this step,
2 Press TIMER repeatedly
until 0 appears on the
display.
When using the remote control,
press TIMER
while pressing
SHIFT.
Time and audio source
name flash alternately.
o
3 Within 6 seconds, turn MULTI JOG to designate
the timer-on time, then press ENTER or Il.
Turning
MULTI JOG changes
both the hour and the minute.
<
or *
is also available
instead
of MULTI JOG, Holding
these buttons
down will vary the time rapidly.
4 Within 4 seconds, turn MULTI JOG to select the
duration for the timer-activated
period.
The duration
can be set between
5 and 240 minutes
in 5-
minute
steps.
-
or ~
is also available
instead
of MULTI JOG,
5 Adjust the volume.
K
The source sound will play at the volume
level set in this step
,$
when the power is turned
on by the timer,
If the volume
level is set to 21 or higher,
however,
it will
~,~?~
automatically
be set to 20 when the power is turned
on.
;$SG
6 Prepare the source.
#&
,,.,,,,
f
,\., -".$
To listen to a CD, load the disc to be played first on tray 1.
'$: ':
To listen to a tape, insert the tape into deck 1 or 2.
'!, !.;
To listen to the radio, tune in to a station.
$
7 Press POWER to turn off the power.
When
the timer-on
time
is reached,
the unit turns
on and
begins
play with the selected
source.
m
You can change the source that was selected in step 1 by pressing
one of the function
buttons before pressing
ENTER or II in step
3.
To check
the timer
setting
Press TIMER.
The selected
source, the timer-on
time, and the duration
for the
timer-activated
period will be displayed
for 4 seconds.
To change
any of the previous
setting
Carry out from step 1.
However,
if you do not change
the timer-on
time, in step 3 just
press ENTER
twice and continue
from step 4.
To cancel
the timer
standby
mode
temporarily
Press TIMER
repeatedly
so that ~ disappears.
To restore the timer standby
mode, press again to display
~.
Using
the unit wlhile the timer
is set
You can use the unit normally
after setting the timer.
Before turning
off the power, carry out step 5 and 6.
m
Timer
playback
and timer recording
will not begin
unless the
power is turned
off.
Connected
equipment
cannot be turned on and off by the built-
in timer of this unit,
Use an external
timer.
;.,, .,.,,, = ,......... ., , . ,
- ..8".8 88 0d.8!!J 8'0.. !0!'!!'10'!8!
TIME'i"REctiRiiNG
Timer recording
is applicable
for TUNER
and VI DEO/AUX
(with
an external
timer) sources
only.
Press either TUNER/BAND
or VIDEO/AUX
to select a source,
then press TIMER
repeatedly
until @REC
lights
up cm th(~
display.
Within
6 seconds,
carry out the steps of "SETTING
THE TIMER"
from step 3 and insert the tape to be recorded
on
into deck 2 after step 6,
m
c
When the power-economizing
mode (page 7) has been turned
on, the timer recording
volume
level will be O (minimum
level).
You cannot
use the timer function
to record from a CD or tape.
The duration
will be automatically
set after 4 seconds,
It will
also be set if ENTER
or I I is pressed
within 4 seconds
after
step 4.
ENGLISH
27
Publicidad
