Publicidad
Idiomas disponibles
Idiomas disponibles
Inserting
batteries
Detach
the battery
cover on the rear of the remote
control
and
insert two R6 (size AA) batteries.
R6(AA)
When
to replace
the batteries
The maximum
operational
distance
between
the remote
control
and the sensor on the main unit should be approximately
5 meters
(16 feet).
When this distance
decreases,
replace
the batteries
with new ones.
To
use
SHIFT
on the remote
control
Buttons
o
have two different
functions.
One of these functions
is indicated
on the button,
and the other on the plate above the
button.
To use the function
on the button,
simply
press the button.
To use the function
on the plate
above
the button,
press the
button while pressing
SHIFT.
To
use
FUNCTION
on the remote
control
FUNCTION
substitutes
for the function
buttons
(TAPE/DECK
1/
2, TUNER/BAND,
VIDEO/AUX,
CD, MD) on the main unit.
Each time FUNCTION
is pressed,
the next function
is selected
cyclically.
When tapes are inserted
in both decks, each deck is
selected
with FUNCTION.
0/+
PRESET
on the remote control
The function
is the same as that of +>
on the main unit.
0
SHIFT
FUNCTION
W+
b
PRESET
m
If the remote
control
is not going to be used for an extended
period
of time,
remove
the batteries
to prevent
possible
electrolyte
leakage.
The remote control
may not operate
correctly
when:
- The line of sight between
the remote control
and the remote
sensor
inside the display
window
is exposed
to intense
light,
such as direct sunlight
- Other remote controls
are used nearby (those of a television,
etc.)
ENTER
MULTI JOG
..— —. .
'1
To turn
the power
on
Press
one of the function
buttons
(TAPE/DECKl/2,
TUNERI
BAND,
VIDEO/AUX,
CD, MD). Playback
of the inserted
disc or
tape begins,
or the previously
tuned
station
is received
(Direct
Play Function).
pOWER
is also available.
m
When the power
is turned
on, the disc compartment
may open
and close to reset the unit.
To
turn the power off
Press POWER.
Flash
window
The window
on the top of the unit and the cassette
decks light
up or flash while the unit is being powered
on.
To turn off the light of the top window,
press
while pressing
CD. To turn back on, repeat the above.
To turn off the light of the cassette
decks, press
while pressing
TAPE. To turn back on, repeat the above.
To
change the brightness level of the display
1
2
3
Press~CO
so th;t 'rECO MODE
is displayed.
-
Within
4 seconds,
turn MULTI JOG to display
"DIM MODE,
and then press ENTER
within 4 seconds.
Within 4 seconds,
turn MULTI JOG to select the dimmer
mode
as below.
The mode
will be automatically
set after 4 seconds.
It will
also be set if ENTER
is pressed
within 4 seconds
after step
3.
DIM-OFF ~DIMMER
1 u
DIMMER
2~DlMMER
3
DIM-OFF:
The normal
display.
DIMMER
1:
The illumination
of the display
is dimmer
than
usual.
DIMMER
2: The illumination
of the display
is dimmer
than
DIMMER
1.
DIMMER
3: The illumination
of the display
is dimmer
than
DIMMER
2. The spectrum
analyzer,
the window
on the top of
the unit, and the button
lamps light off.
If the timer recording
(page 27) is done with the economizing
mode (page 7) set to "ON" and the power turns off, the dimmer
mode will be set to "DIMMER
3" the next time the power
is
turned
on.
6
ENGLISH
Publicidad
