Publicidad
Idiomas disponibles
Idiomas disponibles
Page 9
MAKE-UP AiR DAMPER
GR
MODEL EW56, EW58, EI59 SERIES
MAKE-UPAIR DAMPER
MAKE UP DAMPER
CONNECTION
=
(switched
low voltage)
20 GAUGE
BELLWIRE
FOR LOW
I I
[_
VOLTAGE
CONNECTION
ON
TOP OF HOOD
0,
_]_
TRANSFORMER
/
I_
DRY CONTACT
J411 1
(INCLUDED)
/
I
TERMINAL
)/I
ttl
/
HOOD
I
BUSHING
L44-J
/
I
FOR LOW
I L
120 VAC
,/
I
VOLTAGE
60 HZ
[
I
CONNECTION
The hood is compatible with Broan Make-Up Air Damper Model MD6T or
Model MDST (optional). Purchase separately.
Make the connection to the Make-Up Air Damper with low voltage
wiring, as shown. See Make-Up Air Damper instructions for additional
information.
REMOTE CONTROL
The hood is compatible with Broan Radio Frequency (RF) Remote
Control Model BCR1 (optional). Purchase separately.
Tolink the BCR1 remote control withthe hood, press and hold the LIGHT
buttonfor 3-seconds.
The blue LED indicatorswill turn on and off in succession to indicate the
hood is in RF linking mode. When in the linking mode, press any key on
the RF remote.An audible beep will be heard at the hood, and the hood
LED's will stop blinking if a successful link is accomplished. If the remote
control did not successfully link with the hood, the linking mode will be
deactivated after 12 seconds, and the LED's will stop the sequential
blinking.Refer to the BCR1 instructions for additional information.
CLEANING
& MAINTENANCE
For performance, appearance, and health reasons, clean filter, fan and
grease-laden surfaces.Useonly a clean cloth and milddetergent solution
on stainlessand paintedsurfaces.Clean all-metalfilters inthe dishwasher
using a non-phosphate detergent. Discoloration of the filter may occur if
using phosphate detergents, or as a result of local water conditions- but
this will not affect filter performance.This discoloration is not covered by
the warranty. Clean the non-duct recirculating filter surfaces frequently
with a damp cloth and a mild detergent. DO NOT immerse filters in
water or put in dishwasher. Change the non-duct recirculating filters
every 6 months. For replacement non-duct recirculating filters- purchase
$99010365 or Model FILTERE56.The motor is permanently lubricated
and never needs oiling. If the motor bearings make excessive or unusual
noise, replacethe blower assembly with an exact service replacement.
LIGHT BULBS
SUCTION CUP TOOL
HALOGEN
\
ROTATE
CLOCKWISE_
WARNING
Bulbs may be hot.Always allow bulbs to cool down before removing
them.
Use (2) Halogen Bulbs (included with hood) - 120 V, 35 W, shielded
halogen bulbs- MR16 with GU10 base.
NOTE
Suction Cup Tool(included with hood) can be used to installand
remove light bulbs.Align pins on bulb with large diameter opening
on socket, then push bulb in towards hood and rotate clockwise until
firmly seated.The position of the bulb socket (depth) is adjustable and
may require adjustment when: a) certain brands of bulbs are difficult to
install, b) the bulb protrudes too far below the light panel.
LAMP SOCKET
BRACKET
LIGHT
PANEL
SCREWS
Tochange the depth of bulb sockets:
- Remove 2 screws on light panel - set screws aside
- Remove Light Panel.
- Loosen 2 Screws holding Lamp Socket Bracket to Light Panel.
- Adjust socket/bracketto desired depth.
- Re-tighten screws securely.
- Re-attach light panel with 2 screws that were previously set aside.
Publicidad
