Hoover CAP1700D 011 Manual De Instrucciones página 5

GETTING TO KNOW YOUR CLEANER
A. Steam Release Trigger *
B. Handle Assembly
B1a. Steam Boost Button*
B1b. Variable Steam Release Control Slider Maximum, Medium & Low *
C. Upper & Lower Cord Storage Hooks
D. Power Cord
E. Metal Tube
F. Cleaner Main Body
G. Handle Release Button
H. Cleaner Carry Handle
I. Clean Water Tank Release Latch
J. Clean Water Tank
K. Hard Water Filter
L. Power On /Off Button
M. Power On Indicator Light ( Metallic Red )
N. Steam Ready Light ( Green )
O. Handle Storage Location
P. Floor Head**
P1a. Triangular Brush*
P1b. Triangular Brush Release Pedal *
Q. Textile Pads
R. Carpet Glider
S. Glider release pedal
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Insert the Handle Assembly pole into the Cleaner Main body until it locks into
position. [1]
2. Assemble the main body of the cleaner to the Triangular Brush. [2]
3. Assemble the main body of the cleaner to the floor Head and assemble the Triangular
Brush into the Floor Head.* [3]
USING YOUR CLEANER
BEFORE YOU BEGIN CLEANING
1. Release the clean water tank by sliding the water release button upwards and
remove tank from cleaner main body. [5]
Twist the cap anti clockwise and remove. [6]
2.
Fill the clean water tank with cold tap water. Replace cap. [7] Do not
3.
add any chemicals, detergents or perfumes to the clean water tank.
*Certain Models Only **Nozzle design may vary according to models
4. Re-fit the clean water tank to the cleaner ensuring the hard water filter is in place.
5. Attach a textile pad to the base of the floor Head. [8]
IMPORTANT: Always unplug the cleaner when adding water or changing
a textile pad.
NOTE: Wash the textile pad prior to use to remove any lint.
STEAM CLEANING HARD FLOORS
NOTE: Always sweep or vacuum the floor prior to use to remove any loose
dirt or debris.
IMPORTANT: Do not use the cleaner without a textile pad attached to the
floor head.
NOTE: Do not use the carpet glider when cleaning hard floors.
1. Plug the steam cleaner into the main power. The red ON light will illuminate.
2. After a few seconds the green Steam Ready light will
illuminate indicating the cleaner is ready for use.
3. Recline the cleaner by placing a foot on the floor head and
lowering the main body towards the floor. [9]
To produce steam press the Steam Trigger Button. [10]*
4.
5. Move the cleaner slowly backwards and forwards paying
particular attention to high traffic areas. [12]
6. For certain models to produce steam , just select your cleaning setting on
the Slider control located on the handle. Minimum, Medium or Maximum
depending on your specific cleaning requirement and recline the cleaner. [11]*
7. On Certain model the cleaner is equipped with a steam boost button
located on the Handle. This allow the user to apply extra cleaning
power for 10 seconds to help remove stubborn marks. [11]*
Steam cleaning hard floor - intensive clean
Use the triangular floor brush for hard floors that require deep cleaning. Please note that
there is no mop and the area will have to be dried separately.
NOTE: Always sweep or vacuum the floor prior to use to remove any loose dirt or debris.
1. Remove the triangular floor brush from the floor head by pressing the release pedal
at the rear of the floor head. [13]
2. Plug the steam cleaner into the main power. The red ON light will illuminate. After
a few seconds the green Steam Ready light will illuminate indicating the cleaner is
ready for use.
3. Recline the cleaner by placing a foot on the floor brush and lowering the main body
towards the floor. [14]
To produce steam press the trigger release button. [10]*
4.
5. For certain models to produce steam, just select your cleaning setting on the
Slider control located on the handle. Minimum, Medium or Maximum depending
on your specific cleaning requirement and recline the cleaner. [11]*
6. On Certain model the cleaner is equipped with a steam boost button
located on the Handle. This allow the user to apply extra cleaning
power for 10 second to help remove stubborn marks. [11]*
2
GB