Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING
2. NEVER POINT TOOL AT YOURSELF OR OTHERS
IN WORK AREA.
Always assume the Stapler contains fasteners.
Never point the Stapler at yourself toward yourself or
others, whether it contains fasteners or not.
If fasteners are mistakenly driven, it can lead to
severe injuries.
Never engage in horseplay with the Stapler.
Respect the Stapler as a working implement.
3. KEEP FINGERS AWAY FROM TRIGGER WHEN
NOT DRIVING FASTENERS TO AVOID
ACCIDENTAL FIRING.
Never carry the Stapler with finger on trigger since
you could drive a fastener unintentionally and injure
yourself or someone else.
Always carry the Stapler by the handle only.
4. CHOICE OF TRIGGERING METHOD IS
IMPORTANT.
Read and understand section titled "Method of
operation." (page 19)
5. ALWAYS WEAR EAR AND HEAD PROTECTION.
Always wear ear protection to protect your ears from
loud noise.
Always wear head protection to protect your head
from flying objects.
6. OPERATE WITHIN PROPER TEMPERATURE
RANGE.
The operating environment for this device is between
32°F (0°C) and 104°F (40°C) so ensure use within
this temperature range.
The device may fail to operate below 32°F (0°C) or
above 104°F (40°C).
7. STORE STAPLER PROPERLY, AND BATTERY
REMOVED.
When not in use, the Stapler, battery and battery
charger should be stored in a dry place. Keep out of
reach of children. Lock the storage area.
8. KEEP WORK AREA CLEAN.
Cluttered areas invite injuries. Clear all work areas of
unnecessary tools, debris, furniture, etc.
9. KEEP VISITORS AWAY.
Do not let visitors handle the Stapler.
All visitors should be kept safely away from work
area.
10. DRESS PROPERLY. Do not wear loose clothing or
jewelry as they can be caught in moving parts.
Rubber gloves and nonskid footwear are
recommended when working outdoors.
Wear protective hair covering to contain long hair.
11. CHECK PUSH LEVER BEFORE USE.
Make sure the push lever operates properly. (The
push lever may be called "Safety".) Never use the
Stapler unless the push lever is operating properly,
otherwise the Stapler could drive a fastener
unexpectedly. Do not tamper with or remove the push
lever, otherwise the push lever becomes inoperable.
12. KEEP ALL SCREWS AND COVERS TIGHTLY IN
PLACE.
Keep all screws and covers tightly mounted. Check
their condition periodically.
Never use the Stapler if parts are missing or
damaged.
13. DO NOT LOAD FASTENERS WITH TRIGGER OR
PUSH LEVER DEPRESSED.
When loading fasteners into the Stapler,
(1) do not depress the trigger;
(2) do not depress the push lever; and
(3) keep the Stapler pointed downward.
14. KEEP FACE, HANDS AND FEET AWAY FROM
FIRING HEAD DURING USE.
Never place your face, hands or feet closer than
8 inches (200 mm) from the firing head.
A serious injury can result if the fasteners are
deflected by the workpiece, or are driven away from
the point of entry.
15. PLACE STAPLER PROPERLY ON WORKPIECE.
Do not drive fasteners on top of other fasteners or
with the Stapler at too steep of an angle; the fasteners
can ricochet and hurt someone.
16. BEFORE STARTING WORK, CHECK THE
FASTENING OPERATION SWITCHING DEVICE.
This metabo HPT stapler includes a fastening
operation switching device.
Before starting work, check the setting of the
operation switching device.
If the switching device is not set properly, the stapler
will not operate correctly.
17. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.
If the push lever is unintentionally allowed to re-
contact the workpiece following recoil, an unwanted
fastener will be driven.
In order to avoid this undesirable double fire,
○ Intermittent operation (Trigger firing)
(1) Set the switching device to SINGLE SEQUENTIAL
ACTUATION MECHANISM.
(2) Pull the trigger rapidly and firmly.
English
5
Publicidad
