Publicidad
Idiomas disponibles
Idiomas disponibles
English
State of Charge Indicator (Fig. A, C)
The DCBL777 is equipped with a state of charge indicator
This will display the current level of charge in the battery
during use. It does not indicate tool functionality and
is subject to variation based on product components,
temperature and end-user application.
•
The state of charge indicator LEDs
indicating the percent of charge in the battery.
•
When all four state of charge indicator LEDs
the battery is fully charged.
•
When one state of charge indicator LED
charge is low and then it will flash when the battery
is discharged. Remove the battery and charge it.
State of Charge Indicator LED Status
LEVEL OF CHARGE
100% - 75%
50% - 75%
20% - 50%
≤20%
Low battery shutdown
Battery too hot
Proper Hand Position (Fig. H)
WARNING:
personal injury, ALWAYS use proper hand position
as shown.
WARNING:
personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the
main handle
2
.
Switching On (Fig. A, H—J)
WARNING:
CAUTION:
self or bystanders.
CAUTION:
hearing protection. Wear a filter mask if the operation
is dusty. Use of gloves, long pants and substantial
footwear is recommended. Keep long hair and loose
clothing away from openings and moving parts.
1. Switch the blower on by briefly squeezing the
variable speed trigger
speeds as the lever is moved further.
10
6
will illuminate,
6
illuminate,
6
illuminates,
CHARGE INDICATOR
LED COLOR
White
White
White
White
White and blinking.
All four, red and blinking.
To reduce the risk of serious
To reduce the risk of serious
Grip tool firmly when switching on.
Do not point unit discharge at
Always wear safety glasses and
1
. The blower runs at higher
2. Release the variable speed trigger
3. To lock the blower on, fully depress the
6
.
variable speed trigger
button
3
, as shown in Fig. H, I.
nOTE: The speed lock button
as a lock-off button for the variable speed trigger
4. To unlock and stop the blower, press and release the
trigger switch
5. To turn the blower off, press and hold the speed
button
8
as shown in Fig. J, or after sitting idle for 20
seconds the blower will automatically power off.
Adjusting Blower Speed (Fig. J)
The DCBL777 is equipped with a speed indicator
indicator
7
will display the chosen speed of the blower. There
are three speed setting LEDs, ECO mode
standard mode
22
LED). The speed indicator
performance and runtime needed for each job.
1. To set the blower speed, switch the blower on by briefly
squeezing the variable speed trigger
2. Press the speed button
until the desired speed LED is illuminated.
nOTE: ECO mode
(orange LED) or turbo mode
nOTE: The blower defaults to ECO mode
3. Operate in ECO mode
mode
22
(orange LED) speed for most blowing needs.
nOTE: Longer runtime will be achieved.
4. Choose turbo mode
heavy debris.
nOTE: Runtime will be reduced.
Speed Setting LED Colors
—
21
—
22
—
23
Use (Fig. H)
CAUTION:
self or bystanders.
1
to stop the blower.
1
and then push the speed lock
3
is not intended to function
1
or press the speed lock button
21
(white LED),
(orange LED) and turbo mode
7
helps you to optimize the tool's
1
8
, located on the tool handle,
21
(white LED), standard mode
23
(red LED).
21
(white LED) or standard
23
(red LED) as needed to clear
SPEED
SPEED SETTING LED COLOR
ECO Mode
Standard
Orange
Mode
Turbo Mode
Do not point unit discharge at
1
.
3
.
7
. The speed
23
(red
.
22
21
(white LED).
White
Red
Publicidad
