Parkside Performance PWSAP 20-Li E6 Traduccion Del Manual De Instrucciones Originale página 41

Special safety instructions
for working with wire
brushes
a)­ Be aware that the wire brushes
also lose wire pieces during typi-
cal use. Do not overload the wi-
res by pressing down too hard.
Flying­wire­pieces­can­very­easily­penet-
rate thin clothing and/or your skin.
b)­ If a protective hood is recom-
mended, do not allow the wire
brushes and the protective hood
to touch each other. The­diameter­
of plate and cup brushes can enlarge if
too much pressure and centrifugal force
is exerted.
Additional safety
instructions
•­ Only­use­grinding­discs­where­the­in-
dicated rotational speed is at least as
high­as­what­has­been­specified­on­the­
name­plate­of­the­device.
•­ Carry­out­a­visual­inspection­of­the­
grinding disc before use. Do not use
any damaged or deformed grinding
discs. Replace any damaged or worn
grinding discs.
•­ Make­sure­that­the­sparks­produced­by­
grinding do not present a danger, e.g.
reach­people­or­ignite­flammable­subs-
tances.
•­ Always­wear­safety­goggles,­safety­
gloves,­respiratory­protection­and­ear­
protection when grinding, brushing and
cutting.
•­ Never­keep­the­fingers­between­the­
grinding disc and spark protection or in
close­proximity­to­the­protective­hoods.­
There­is­a­risk­of­crushing.
•­ The­rotating­parts­of­the­device­cannot­
be­covered­due­to­functional­reasons.­
Therefore,­proceed­cautiously­and­hold­
the­workpiece­firmly­in­order­to­avoid­
slipping which could cause your hands to
come into contact with the grinding disc.
•­ The­workpiece­gets­hot­during­grinding.­
Do not touch the machined area, allow
it­to­cool­down.­There­is­a­risk­of­bur-
ning. Do not use coolants or the like.
•­ If­you­are­tired­or­have­consumed­al-
cohol or tablets, do not work with the
device.­Always­have­a­break­on­time.
•­ Switch­off­the­device­and­remove­the­
battery­from­the­device
-­ to­loosen­a­blocked­insertion­tool,
-­ if­the­connection­line­is­damaged­or­
entangled,
-­ in­case­of­unusual­sounds.
•­ When­using­a­guard­cover­of­type­A­
(cutting­guard­cover)­for­side­grinding,­
the guard and the workpiece may interfe-
re­with­each­other,­resulting­in­insufficient­
control.
•­ When­using­a­guard­cover­of­type­B­
(grinding­guard­cover)­for­cut-off­grin-
ding­with­bonded­cut-off­wheels,­there­
is an increased risk of being exposed to
the ejected sparks and grinding partic-
les as well as fragments of the grinding
wheel­in­the­event­of­a­grinding­wheel­
breakage.
•­ When­using­a­guard­cover­of­type­A­
guard­cover­(cutting­guard­cover)­or­
type­B­(grinding­guard­cover)­for­cut-off­
or side grinding in concrete or mason-
ry, there is an increased risk due to
dust exposure as well as loss of control
with kickback as a consequence.
•­ When­using­a­guard­cover­of­type­A­
(cutting­guard­cover)­or­type­B­(grin-
ding­guard­cover)­with­a­wheel­brush­
thicker­than­the­maximum­specified,­the­
wires­may­hit­the­guard­cover­and­this­
may cause the wires to break.
GB MT
41