Generac iX 1600 Manual Del Propietário página 9

Figure6 -AdjustChoke
ADDING LOADS
Once the generator has been running smoothly for 2-3 minutes,
electrical loads can be added.
Do not use worn, bare, frayed or otherwise
damaged electrical cord sets with the
generator. Do not handle any kind of
electrical device while standing in water,
while barefoot, or while hands or feet are
wet.
1. Thereare two grounded 120 VAC duplex outlets on the front
of the generator.
2. DONOToverloadthe generator;if the red "overload" LEDlights
up and the devices attachedto the generatorstop operating,
stop the engine and reducethe load to the generator.Restart
and apply reducedloads.
3. Consultthe following table to estimate what can be powered
by the generator.
Device ................................ Running Watts
*Air Conditioner (12,000Btu) ......................... 1700
*Air Conditioner (24,000Btu) ......................... 3800
*Air Conditioner (40,000Btu) ......................... 6000
BatteryCharger(20 Amp) ............................. 500
BeltSander(3").................................... 1000
ChainSaw........................................ 1200
CircularSaw (6-1/2").......................... 800 to 1000
*ClothesDryer (Electric)............................. 5750
*ClothesDryer (Gas)................................. 700
*ClothesWasher................................... 1150
CoffeeMaker...................................... 1750
*Compressor(1 HP)................................ 2000
*Compressor(3/4 HP)............................... 1800
*Compressor(1/2 HP)............................... 1400
CurlingIron ........................................ 700
*Dehumidifier ...................................... 650
DiscSander(9") ................................... 1200
EdgeTrimmer ...................................... 500
ElectricBlanket..................................... 400
ElectricNailGun .................................... 1200
ElectricRange(per element) .......................... 1500
ElectricSkillet ..................................... 1250
*Freezer . .......................................... 700
*FurnaceFan(3/5 HP)................................ 875
*GarageDoorOpener ........................... 500 to 750
HairDryer ........................................ 1200
HandDrill................................... 250 to 11O0
HedgeTrimmer ..................................... 450
ImpactWrench ..................................... 500
Iron ............................................. 1200
*Jet Pump......................................... 800
LawnMower ...................................... 1200
LightBulb ......................................... 1O0
MicrowaveOven............................. 700 to 1000
*Milk Cooler ...................................... 1100
Oil Burneron Furnace . ................................ 300
Oil FiredSpaceHeater(140,000Btu)..................... 400
Oil FiredSpaceHeater(85,000Btu) ...................... 225
Oil FiredSpaceHeater(30,000Btu) ...................... 150
*Paint Sprayer, A irless (1/3 HP)......................... 600
PaintSprayer, A irless (handheld)........................ 150
Radio........................................ 50 to 200
*Refrigerator....................................... 700
SlowCooker ....................................... 200
*SubmersiblePump(1-1/2 HP)........................ 2800
*SubmersiblePump(1 HP)........................... 2000
*SubmersiblePump(1/2 HP).......................... 1500
*Sump Pump ................................ 800 to 1050
* Allowthree(3) timesthe listed runningwatts for startingtheses
devices.
NOTE:
When an electric motor is started, the "OVERLOAD" L ED may
light up for up to five (5) seconds(this is normal).If it stayson,
a fault hasoccured. Removeall loadsand shutdowngenerator
to reset the alarm. Restart the generator. If the "OVERLOAD"
LED remainslit, contacta GeneracDealerfor assistance.
USING THE FLEXPOWER'" SWITCH
When the accessories connected to the generator are going to
be used intermittently (such as a hand drill), the FtexPower
TM
switch can be pushedto the "ON" (I) position. This will lower the
generatorengine speed when loads are not being applied,saving
fuel, reducingengine wear and extendingruntime.