Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
20
Circlip D32
4
21
Hex head screw M8x30
2
22
Phillips screw M6x10
12
23
Phillips screw M5x12
6
24
Cross-threaded screw
11
ST4.2*18
25
Plain washer
2
D10*Φ58*3
26
Cross-threaded screw
4
ST3.9*12
27
Spring washer D10
6
28
Spring washer D8
18
29
Closing plug
2
30
Plain washer
6
D10*D20*2
31
Plain washer D8*D32*2
2
32
Plain washer D8*D26*2
4
33
Plain washer D8*D20*2
4
34
Plain washer
10
D8*D16*1.5
35
Balance shaft Φ20*498
1
36
Wave washer
6
Φ8*1.5*Φ20
37
Curved washer D21
2
38
Curved washer D17
2
39
Ferrule
2
40
Nylon nut M8
4
56
DRUMFIT ELLIPTICAL 10000 MOTOR PRO
60a/b
Protective cover
2
61
Protective cover
2
62
Cap
2
63
Friction bushing
4
Φ42xΦ17x23
64
Friction bushing
4
Φ32*Φ26.8*Φ19*28
65
Foam handle
4
φ31*T3*10
Foam handle
66
2
Φ31×Φ37×600
67
Screw cap
2
68
Oval plug
2
69
Feet
2
70
Adjustable pad
2
71
Circular plug
2
72
Flat oval plug
4
73
Heart rate monitor
2
74
Ferrule
2
75a/b
Console cover
1
76
Console
2
77
Phillips screw
4
M5*10
78
Sensor cable
1
79
Extension lead
1
80
Pulse cable
2
81
Oval arc plug
NOTE
:
the graphics in this manual are schematic representations and may not exactly match the
device.
2. BEFORE USE
-
This appliance is packaged in a way as to protect it during transport. Take the device out
of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the device when
transporting it in the future. In case the original packaging is disposed of, make sure all
packaging materials are recycled accordingly.
-
Make sure all parts and components are included and in good conditions. If there is any
piece missing or in bad conditions, contact the official Cecotec Technical Support Service
immediately.
Box content
-
Drumfit Elliptical 10000 Motor Pro elliptical cross trainer
-
Assembly kit
-
Instruction manual
-
Power adapter
3. ASSEMBLY
Step 1 (Fig. 2)
Unscrew the bolt (B), washers (C, D) and nut (E) from the main frame (1) and remove the closing
plug (A).
Step 2 (Fig. 3)
1.
Attach the feet (69) to the front lower stabiliser (10).
2.
Lock the front lower stabiliser (10) on the main frame (1) using the spring washer (27) and
plain washer (30).
3.
Remove the screw cap (67) from the guides (3L/R) as shown in figure A.
4.
Insert the hinged shaft (4) into the hole in the main frame (1). Then, firmly fix the guides
(3L/R) on the hinged shaft (4) with the screw (12), spring washer (27) and plain washer
(25).
5.
Finally, fit the screw cap (67).
Step 3 (Fig. 4)
Insert the protective cover (52) into the handlebar stem (2); connect the sensor cable (78)
1.
ENGLISH
DRUMFIT ELLIPTICAL 10000 MOTOR PRO
57
Publicidad
