Toto TES201AB Serie Manual De Instalación Y Del Propietario página 17

SPECIFICATIONS
Kit Model TES201A Series TES202A Series TES204A Series TES203A Series TES205A Series
Configuration
Power supply
Wattage 4 W
Sensor 5-1/8'' – 7-7/8'' (130–200 mm)
detection range
Ambient
Temperature
Humidity
Power Cord
Length
Soap volume
Tank
For TES201(2/3)A Series: Approximately 0.8 gallon (3 L) (Usable Capacity)
Capacity
For TES204(5)A Series : Approximately 6.1 gallon (23 L) (Usable Capacity)
AC 120 V
6.5 W 9 W
sensor is self-adjusting
34–104°F (1–40°C)
Max.90% RH
55'' (1.4 m)
0.04 o.z (1.2 ml)
(at factory setting)
32
MAINTENANCE WARNINGS - IoT Communication Card
Follow these instructions carefully. Failure to do so could result in personal injury, risk
of fire, smoke and/or property damage.
- Handle the product with care when performing maintenance.
- DO NOT pull, twist or damage the wires or connectors. Risk of product malfunction.
- NEVER splash water on the components. This is an electrical device.
DO NOT get the components wet. Risk of product malfunction.
Follow these instructions carefully. Failure to do so could cause incorrect data reporting.
- Each IoT communication card has been electronically paired to a specific controller.
DO NOT MIX UNPAIRED SIMILAR COMPONENTS EVEN WHEN VISUALLY IDENTICAL.
- When performing maintenance, please keep track of paired components.
- Make sure paired IoT communication card reconnects to it's exact corresponding paired controller.
- Failure to reconnect corresponding paired components will result in product malfunction.
REGULATORY STATEMENTS - IoT Communication Card
FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Interference Statement Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled
exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 43mm from all persons and must not be operating in conjunction with any other antenna or
transmitter, except in accordance with FCC multi-transmitter product procedures.
Industry Canada:
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to
the following two conditions: 1) this device may not cause interference, and 2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada, exempts de licence standard RSS (s). Son
fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut pas causer
d'interferences. et 2) ce dispositif doit accepter toute interference, y compris les interferences qui
peuvent causer un mauvais fonctionnement de ('appareil.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
33