EINHELL TE-SY 18/90 Li Manual De Instrucciones Original página 21

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 24)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a dust mask. Harmful mist can
form when processing paints and lacquers.
Note the information provided by the manu-
facturer of the materials you are processing.
Use suitable safety masks to protect yourself.
4. Caution! Wear safety goggles. Note the in-
formation provided by the manufacturer of the
materials you are processing. Wear suitable
eye protection (goggles) to protect yourself.
5. Caution! Wear gloves.
6. Note! Disassemble and clean the equipment
immediately after each use. This is the only
way to keep the wetted parts clean and pre-
vent clogging. Parts that are not cleaned can
become clogged, causing an equipment fault.
7. Store the batteries only in dry rooms with
an ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%).
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Anl_TE_SY_18_90_Li_SPK13.indb 21 Anl_TE_SY_18_90_Li_SPK13.indb 21
GB
2. Layout and items supplied
2.1 Layout (Fig. 1-4, 14, 17, 21-23)
1. Union nut
2. Air cap
3. 3.0 mm nozzle
4. Locking lever
5. Trigger
6. Control screw for paint volume
7. Control lever for air volume
8. Handle
9. Viscosity cup
10. Riser pipe seal
11. Riser pipe
12. Container
13. Fluid needle (plastic)
14. Trigger unit
15. Drive unit
16. Filter cap
17. Shoulder strap
18. On/Off switch
19. Air hose
20. 1.5 mm nozzle
21. 2.5 mm nozzle
22. Air pipe
23. Seal cap
24. Seal
25. Air inlet fi lter
A. Cleaning needle
B. Fluid needle adapter
C. Cleaning brush
a. Battery charge level indicator
b. Battery charge level indicator (LEDs)
c. Pushlock button
d. Li-ion battery pack
(not supplied with this product)
e. Power X-Charger
(not supplied with this product)
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
- 21 -
26.10.2023 15:51:36 26.10.2023 15:51:36