EINHELL TE-SY 18/90 Li Manual De Instrucciones Original página 23

Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Charging the LI battery pack (Fig. 1d, 2-3)
1. Remove the battery pack (d) from the drive
unit by pressing the pushlock button (c)
downwards.
2. Check that your mains voltage is the same
as that marked on the rating plate. Insert the
power plug of the charger (e) into the mains
socket outlet.
3. The green LED will then begin to fl ash.
Push the battery pack onto the battery charger. In
section 12 (Charger indicator) you will fi nd a table
with an explanation of the LED indicator on the
charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_TE_SY_18_90_Li_SPK13.indb 23 Anl_TE_SY_18_90_Li_SPK13.indb 23
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 2/Pos. b)
Press the button for the battery capacity indicator
(a). The battery capacity indicator (b) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too high. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.3 Assembling the spray gun (Fig. 4, 5, 6)
Plug the riser pipe (11) with seal (10) onto the
trigger unit (14) and then screw the container (12)
on the trigger unit. The trigger unit (14) is attached
to the handle (8) by means of a bayonet connec-
tor. To begin with, hold the trigger unit and the
handle (8) at an angle of 90°; the correct position
is indicated by arrows on both components.
Hold the locking lever (4) open. Twist and insert
the trigger unit (14) into the handle. Close the
locking lever.
5.4 Fitting the air hose (Fig. 6)
The handle (8) and the air hose (19) are marked
with arrows indicating the locking position: Con-
nect – turn counter-clockwise. Disconnect – turn
clockwise. Fasten the hose by twisting it into the
handle.
Fasten the other end of the hose to the drive unit
in the same way.
- 23 -
26.10.2023 15:51:37 26.10.2023 15:51:37