Publicidad
Idiomas disponibles
Idiomas disponibles
REPLACING
THE
LINE
1.
Remove
spool
by firmly
pulling
on tap
button.
2.
Clean entire surface
of hub and spool.
3.
Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080" (2 mm) di-
ameter Poulan PRO brand line.
_WARNING:
Never
use wire, rope,
string, etc., which can break offand
become a
dangerous
missile.
4.
Insert ends of the lines about t/2 h_ch (1
cm) into the small holes on the inside of
spool.
spoo__//"Zi_
8
sma,
_/
_/'_i_
Holes
Line exit holes
\
Line in Notch
5.
Wind the line evenly and tightly
onto the
spool. Wind in the direction
of the arrows
found on the spool.
6.
Push the lines into the notches,
leaving 3
to 5 inches (7 - 12 cm) unwound.
7.
Insert the lines into the the exit holes in
the hub as shown
in the illustration.
8.
Align the notches with the line exit holes.
9.
Push spool into hub until it snaps into place.
10. Pull the lines extending outside of the hub
to release the lines from the notches.
CARBURETOR
ADJUSTMENT
_i WARNING:
Keep
others away when
maMng
idle speed
adjustments.
The chain
will be moving during most of this procedure.
Wear your protective
equipment
and observe
all safety precautions.
After making
adjust-
ments, the chain must not move at idle speed.
The carburetor
has been carefuliy
set at the
factory.
Adjustment
to the idle speed may be
necessary
if you notice any of the following
conditions:
• Engine
will not idle when the throttle is re-
leased.
• The chain
moves
at idle.
Make adjustments
with the unit supported
so
the pruner is off the ground and the chain will
not make contact
with any object.
Hotd the
unit by hand while running and making adjust-
ments. Keep all parts of your body away from
the chain and muffler.
Idle Speed Screw
IDLE
SPEED
ADJUSTMENT
Allow engine to idle. Adjust idle speed until en-
gine runs without chain moving
(idle too fast)
or stalling
(idle speed too slow).
• Turn
idle speed
screw
clockwise
to in-
crease engine speed if engine stalls or dies.
• Turn idle speed screw counterclockwise
to
decrease engine speed if chain moves at idle.
_WARNING:
Recheck
the idle speed
after each adjustment,
The chain
must not
move at idle speed to avoid serious
injury to
the operator
or others.
If you require further assistance
or are unsure
about performing
this procedure,
contact your
authorized
service
deaier
or
call
1-800-554-6723.
OWAI-ININLi:
Perform
the following
steps after each use:
• Allow engine to cool before storing or trans-
porting.
• Store unit and fuel in aweH ventilated
area
where fuel vapors cannot reach sparks
or
open flames
from water
heaters,
electric
motors or switches,
furnaces,
etc.
• Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally
cause injury.
• Store unit and fuel well out of the reach of
children.
SEASONAL
STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
• Clean
the
entire
unit
before
lengthy
storage.
• Store in a clean dry area.
• Lightly oil external
metal surfaces.
FUEL
SYSTEM
Under
FUELING
ENGINE
in the OPERA-
TION section of this manual, see message
la-
beled IMPORTANT
regarding
the use of ga-
sohol in your engine.
18
Publicidad
