Publicidad
Idiomas disponibles
Idiomas disponibles
• If the rotor will not rotate freety due to frozen
ice. thaw the unit before thoroughly
before
attempting
to operate under power.
• Keep the rotor clear of debris.
• Do not throw snow near other people.
The
snow thrower could propel small objects at
high speed
causing
injury.
• After striking a foreign
object, stop the en-
gine. disconnect
spark plug and inspect the
snowthrower
for damage
aed repair if nec-
essary
before restarting
unit.
• Never operate the snowthrower
near glass
enclosures,
automobiles
and trucks.
• Never attempt to use the snowthrower
on a
roof.
• Never operate
the snowthrower
near win-
dow wells, dropoffs,
etc.
• Never discharge
snow onto public roads or
near moving traffic.
• Clear
snow from slopes
by going up and
down;
never across.
Use
caution
when
changing
directions.
Never
clear
snow
from steep
slopes.
• Let snowthrower
run for a few minutes after
clearing
snow
so
moving
parts
do
not
freeze.
• Look behind and use care when
backing
up. Exercise caution to avoid slipping or fai-
ling. especially
when operating
in reverse.
• Know how to stop quickly.
AlL
rmWARNING:
If
received
assembled,
repeat ali steps to ensure your unit is properly
assembled
and all fasteners
are secure.
Examh_e parts for damage.
Do not use dam-
aged parts.
NOTE:
If you need assistance
or find parts
missing
or damaged,
call 1-800-554-6723.
It is normal
for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue
on muffler is normal
due to carburetor
adjustments
and testing
done by the manufacturer.
TOOLS
REQUIRED
• Hex wrench
(provided)
INSTALLING
PRUNER
OR LINE
TRIMMER
ATTACHMENTS
CAUTION:
When removing
or installing at-
tachments,
place the unit on a flat surface
for
stability.
1.
Loosen
the coupler
by turning
the knob
counterclockwise.
Coupler
Primary
Hole
Guide Recess
Upper
Locking/
Lower
Release
Shaft
Attachment
Button
ill
m_WARNING:
Make sure the locking/
release
button
is locked
in the primary hole
and the knob is secureiy
tightened
before op-
erating
the unit. All attachments
are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment
instruction
manual Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Secondary
Hole
Coupler
Shipping
protector
Knob
TIGHTEN
2.
Remove
shipping protector
from coupler.
3.
Remove
the shaft cap from the attach-
ment (if present).
4.
Position locking/release
button of attach-
ment into guide recess
of coupler.
5.
Push the attachment
into the coupler
until
the locking/release
button snaps into the
primary hole.
6.
Before using the unit. tighten the knob se-
curely
by turning clockwise.
Locking/Release
Button in Primary
Hole
For
optional
attachments,
see
the
AS-
SEMBLY
section
of the applicable
attach-
ment instruction
manual.
SHOULDER
STRAP
ASSEMBLY
_,WARNING:
Proper
shoulder
strap
adjustments
must be made with the engine
completely
stopped
before using unit.
1.
Try on shoulder
strap and adjust
for fit
and balance before starting
the engine or
beginning
a cutting operation.
2.
Insert your right arm and head through
the shoulder
strap and allow it to rest on
your left shoulder.
Make sure the danger
sign is centered
on your
back and the
hook is to the right side of your waist.
NOTE:
A one-half
twist is built in the shoul-
der strap to allow the strap to rest fiat on the
shoulder.
8
Publicidad
