Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para Kyocera Mita DF-670
Resumen de contenidos para Kyocera Mita DF-670
- Página 1 INSTALLATION GUIDE FOR BUILT-IN FINISHER...
- Página 2 F Upper left cover..........1 English G Front eject cover ..........1 H Rear eject cover..........1 Finisher tray ...........1 Supplied parts J Staple cartridge ..........1 A Paper conveying unit........1 K Blindfold seal..........1 B Sub staple cover..........1 L Large pin ............1 C Staple cover...........
- Página 3 Precautions Important Procedure When placing the paper conveying unit (A) on Removing the covers ･ Be sure to remove any tape and/or 1. Open the front cover (1) and left cover 1 (2). the floor or the like, be sure to place it upside cushioning material from supplied parts.
- Página 4 4. Release the latch (7) using a flat-head 5. Remove the screw (9) to remove the metal 6. Release the latch (11) using a flat-head screwdriver to remove the cover (8). plate (10). screwdriver and slide the cover (12) to the The removed metal plate (10) is no longer front to remove.
- Página 5 8. Remove the screw (15) from the rear side of Attaching the sub staple cover 9. Insert the hook (17) of the sub staple cover the machine to remove the cover (16). (B) and turn the cover (B) in the direction of arrow until it clicks to attach.
- Página 6 Installing the paper conveying unit 10. Insert the paper conveying unit (A) from the machine front and slide it to the left. 11. Fix the paper conveying unit (A) using two pins. Front: Use the large pin (L). Rear: Use the small pin (M). Installation de l’unité...
- Página 7 Releasing the lever holding plate Installing the finisher process table 12. Loosen the screw (18) of the paper 14. Loosen the screw (20) approx. 3 turns. conveying unit (A) and release the lever Do not turn the screw (20) too far, otherwise it may drop into the machine. holding plate (19) in the direction of arrow.
- Página 8 17. Extend the wires of connectors (22) of the finisher process table (E) straight. 19. At the rear side of the machine, connect the 18. Insert the finisher process table (E) from the front side of the machine and hang the hooks (23) on connector (24) of the finisher process table the right and left of the table (E) onto the machine.
- Página 9 Attaching the upper left cover Installing the staple cover 22. Insert five catches (28) to attach the upper 23. Release two latches (29) of the cover (6) removed in step 3 using a flat-head screwdriver to left cover (F). remove the lower clip holder (30). 24.
- Página 10 25. Fix the staple cover (C) using three screws. 26. Replace the clip holder (3) removed in step Attaching the finisher tray 28. Fix the front eject cover (G) and the rear Upper/Lower right: Use two screws (4) eject cover (H) using an M3 × 6 screw (N) removed in step 3.
- Página 11 29. Insert the front and rear hooks of the finisher Attaching the staple cartridge Adhering the blindfold seal (For models with 30. Open the cover (31) and insert the staple monochrome touch panel only) tray (I) into the front eject cover (G) and the 32.
- Página 12 Checking the operation 1. Connect the power plug of the machine to the wall outlet and turn the main power switch on. 2. Make a proof copy in the staple mode to check the finishing and stapling. Vérification du fonctionnement 1.