Manuales relacionados para Kyocera DF-770
Resumen de contenidos para Kyocera DF-770
- Página 1 INSTALLATION GUIDE GUIDE D’INSTALLATION GUÍA DE INSTALACION INSTALLATIONSANLEITUNG GUIDA ALL’INSTALLAZIONE 安装手册 설치안내서 設置手順書 DF-770(B)
- Página 2 A different procedure is required depending on the product which is installed with this unit.Each procedure is described in the following pages. English For installation with a MFP, see Page 1 to Page 6. For installation with a Printer, see Page 7 to Page 12. Une procédure différente est requise selon le produit qui est installé...
- Página 3 J(M4x20) I(M4x8) K(M4x10) Supplied parts G. Eject guide ..........1 Be sure to remove any tape and/or cushioning A. Document finisher........1 H. Staple cartridge.......... 1 material from supplied parts. B. Eject tray............ 1 I. M4 × 8 screw ..........3 C.
- Página 4 NOTICE Procedure 1.Install by inserting the 2 hooks (1) on the The Attachment Kit (AK-730) must be installed Before starting installation, be sure to turn the back of the eject tray (B) into the holes (2) in before the document finisher is installed. main power switch of the machine off, and the document finisher (A) lift.
- Página 5 J(M4x20) I(M4x8) 2.Secure the upper earth plate (C) and lower 3.Install the eject guide (G) by fitting the 2 4.Attach the connecting plate (E) to the earth plate (D) with M4 × 8 screws (I). eject guide pins (3) into the holes in the machine using 2 M4 ×...
- Página 6 6.Remove the tape and remove the rear cover 7.Remove the screw (5) and pull the lock 8.Insert the 2 pins (8) on the connecting plate (4). frame (6) outwards. (E) into the holes (7) to connect the docu- The connecting holes (7) can now be seen. ment finisher to the machine.
- Página 7 I(M4x8) 9.Push the lock frame (6) in fully so that the 11.Install the wire guide (F) using the M4 × 8 12.Route the signal line (9) through the wire lock frame ribs fit into the pin slots. screw (I). guide (F) and connect it to the connector 10.Secure the lock frame (6) using the screw (10) on the machine.
- Página 8 K(M4x10) 13.Install the back cover (4) using the M4 × 10 14.Attach the interface cover (11)* on the 15.Open the document finisher front cover (12) screw (K). machine. and install the staple cartridge (H). * The cover removed while installing the AK- 16.Close the front cover (12).
- Página 9 AK-735 I(M4x8) J(M4x20) K(M4x10) Supplied parts G. Eject guide ..........1 D is not used. A. Document finisher........1 H. Staple cartridge.......... 1 G is used in AK-735. B. Eject tray............ 1 I. M4 × 8 screw ..........3 C. Upper earth plate........1 J.
- Página 10 NOTICE Procedure 1.Install by inserting the 2 hooks (1) on the The Attachment Kit (AK-735) must be installed Before starting installation, be sure to turn the back of the eject tray (B) into the holes (2) in before the document finisher is installed. main power switch of the machine off, and the document finisher (A) lift.
- Página 11 J(M4x20) I(M4x8) 2.Secure the upper earth plate (C) and the 3.Attach the connecting plate (E) to the 5.Remove the tape and remove the rear cover earth plate (Y)* with M4 × 8 screws (I). machine using 2 M4 × 20 screws (J). (4).
- Página 12 6.Separate the rear cover(4) into the two cov- 7.Remove the screw (5) and pull the lock 8.Insert the 2 pins (8) on the connecting plate ers(4-1,4-2). frame (6) outwards.The connecting holes (7) (E) into the holes (7) to connect the docu- The cover (4-2) is not used.
- Página 13 I(M4x8) 9.Push the lock frame (6) in fully so that the 11.Install the wire guide (F) using the M4 × 8 12.Route the signal line (9) through the wire lock frame ribs fit into the pin slots. screw (I). guide (F) and connect it to the connector 10.Secure the lock frame (6) using the screw (10) on the machine.
- Página 14 K(M4x10) 13.Install the cover (Z)*. 14.Install the cover (4-1) using the M4 × 10 15.Open the document finisher front cover (12) *The part was supplied with the AK-735. screw (K). and install the staple cartridge (H). 16.Close the front cover (12). Proceed to adjusting the stapling position on page 17.
- Página 15 Adjusting the height Compliant: The diameter (a) of the pin (8) is within the height range (b) of the curved section (13). 1.Check that the respective heights of the pins Non-compliant: The diameter (a) of the pin (8) is extends beyond the height range (b) of the curved (8) on the connecting plate installed on the section (13).
- Página 16 2.Remove each of the screws (14) and 3.Remove the screw (17) to remove the span- remove the front foot cover (15) and rear ner (18). foot cover (16). 4.Loosen the 2 screws (19) on the front right and on the rear right of the document fin- isher.
- Página 17 5.Turn the adjustment bolts (20) with the spanner (18) to adjust the height of the document finisher. 7.If the distances between the document fin- Turning the adjustment bolt clockwise lifts the document finisher, and turning it counterclockwise isher and the machine (21, 22) are unequal, lowers the document finisher.
- Página 18 8.Loosen the 2 screws (23) on the front left 9.Turn the adjustment bolts (24) with a Philips-head screwdriver to adjust the height of the docu- and on the rear left of the document finisher. ment finisher. Turning the adjustment bolt clockwise lifts the document finisher, and turning it counterclockwise lowers the document finisher.
- Página 19 78.5mm±2.5 158mm±2.5 Adjusting the stapling position 1.Connect the machine power plug to the wall outlet and turn the machine main power switch on. 2.Make a test copy using staple mode (double stapled). 3.Check whether the stapling position is off-center. If the staple position is off-center, follow the procedure below to adjust the position. <Reference value>...
- Página 20 4.Set maintenance mode U246, select Finisher and Staple HP. 7.Repeat steps 4 to 6 until the staple position is within the reference 5.Adjust the values. value. If the paper is stapled too close to the front of the machine (a): Increase <Reference value>...
- Página 21 MEMO...
- Página 22 MEMO...
- Página 23 MEMO...
- Página 24 2012. 9 303NC56731-01...