Publicidad
Idiomas disponibles
Idiomas disponibles
Occasional
care and maintenance
of the unit and the software
are needed to optimize the performance
of your unit.
To clean the cabinet
Use a soft and dry cloth.
If the surfaces
are extremely
dirty, use a soft cloth lightly
moistened
with mild detergent
solution.
Do not use strong
solvents, such as alcohol,
benzine
or thinner as these could
damage the finish of the unit.
To clean the heads and tape paths
After every 10 hours of use, clean the heads and tape paths
with a head cleaning cassette
or cotton swab moistened
with
cleaning
fluid or denatured
alcohol.
(These
cleaning
kits are
commercially
available.)
When cleaning with a cotton swab, wipe the recording/playback
head, erasure head (deck 2 only), capstans, and pinchrollers.
After cleaning
the heads and tape paths with a liquid head
cleaning cassette
or a moistened
swab, wait until the cleaned
parts are completely dry before inserting the tapes
To demagnetize
the heads
The heads may become magnetized
after long-term use. This
may narrow the output range of recorded tapes and increase
noise.
After 20 to 30 hours use, demagnetize
the heads with
any commercially
available demagnetizer.
Care of discs
When a disc becomes dirty, wipe the disc from the center out
with a cleaning cloth.
* After playing a disc, store the disc in its case. Do not leave the
disc in places that are hot or humid.
Care of tapes
Store tapes in their cases after use.
Do not leave tapes near magnets,
motors, television sets, or
any source of magnetism. This will downgrade the sound quality
and cause noise.
Do not expose tapes to direct sunlight, or leave them in a car
If the unit fails to perform
as described
in these
Operating
Instructions, check the following guide.
GENERAL
There is no sound.
@ Is
the AC cord connected
properly?
o Is there a bad connection?
(+ page 3)
There may be a short circuit in the speaker terminals.
+
Disconnect
the
AC cord,
then
correct
the
speaker
connections.
MWas an incorrect function button pressed?
Sound is emitted from one speaker only.
DIs
the other speaker disconnected?
The output sound is not stereo.
s IS
the Karaoke function turned on? (+ page 19)
An erroneous
display or a malfunction
occurs.
-+
Reset the unit as stated below.
TUNER
SECTION
There
is constant,
wave-like
static.
o Is the antenna connected
properly? (+ page 3)
* Is the signal weak?
+ Connect an outdoor antenna.
The reception
contains
noise
interferences
or the sound
is distorted.
D Is the system picking up external noise or multipath distortion?
+
Change the orientation of the antenna.
+
Move the unit away from other electrical appliances.
CASSETTE
DECK
SECTION
The tape does
not run.
* IS deck 2 in pause mode? (+ page 13)
The
sound is off-balance
or not adequately
high.
* Is
the playback head dirty? (+ page 24)
Recording
is not possible.
Is
the erasure prevention tab on the tape broken off? (+ page
14)
o Is the recording head dirty? (+ page 24)
Erasure is not possible.
* Is
the erasure head dirty? (+ page 24)
* Is a metal tape being used?
High frequency
sound is not emitted.
o Is
a tape recorded without Dolby NFt played back with the Dolby
NR system operating? (+ page 13)
Is the recording/playback
head dirty? (+ page 24)
CD
PLAYER SECTION
The CD player does not play.
*
1s
the disc correctly inserted? (+ page 11)
~ IS the disc dirty? (+ page 24)
@1s the lens affected by condensation?
+ Wait approximately
one hour and try again.
To reset
If an unusual condition occurs in the display window, the cassette
decks or CD player, reset the unit as follows.
1
Press POWER
to turn
off the power.
2
Press
POWER
to turn the power back on while pressing
CLEAR.
Everything
stored
in memory
after purchase
is
canceled.
If the power
cannot
be turned
off in step 1 because
of a
malfunction, reset by disconnecting the AC cord and connect it
again. Then carry out step 2.
ENGLISH
24
Publicidad
