Krups Virtuoso + XP444 Manual Del Usuario página 4

4. Press button (C) (5) on control panel (D).
lights flash white (6). The machine is pre-heating.
5. Place a filter (F2) (7) without coffee into the filter holder. Slot the filter holder into place and turn it
to the right until it stops (8).
6. Place two cups under the filter holder.
7. When the temperature reaches pre-set value,
is in coffee brewing mode. Press
the water (10). When it is finished, buttons
8. Press button (11). Buttons
is pre-heating.
Place the steam nozzle (H) into a container filled with water (12).
9.
10. Turn the knob (M) from preheat (M1) to steam position (M2) (13), button
the machine starts to make steam. Let the water heat for 20 seconds, then turn the knob back to
preheat position (M1) (14).
Note: If you want to brew a coffee now, please refer to the GOOD TO KNOW – PRACTICE AFTER
USING STEAM section to know how to proceed.
MAKING ESPRESSO
IMPORTANT!
If the espresso function is used for the first time, the appliance must be cleaned as
described in the "FIRST USE" paragraph.
IMPORTANT! To prevent splashes of hot water, check that the filter holder has been
tightened until it stops before preparing the coffee. Do not remove the filter holder
while the water is flowing, as the appliance is still under pressure.
With ground coffee
To prepare your coffee, please refer to the first 4 steps in the FIRST USE section and then follow the
instructions below:
The machine is in coffee brewing mode.
5. Add the ground coffee to the 1 cup or 2 cups filter (F1, F2) using the measuring spoon (L, 1 spoon
= 1 measure = +/- 7g of ground coffee = 1 espresso) (15, 16), then pack it down (firmly but not
too solid) using the tamper (17). Do not overfill the filter. Clean off any excess coffee from around
the filter holder (18).
6. Slot the filter holder into place then turn it to the right until it stops (20).
7. Place a cup or two cups under the filter holder.
(21) or (9), according to the number of cups you want to make (15).
8. Press button or button
The selected button will flash and the appliance will start (22). When the machine has finished, the
buttons will stay lit.
9. Unlock the filter holder by turning it to the left (23) and remove it from the appliance.
10. Use the filter holding hook to empty the filter. (24) Remove the filter from the filter holder.
11. Wash the filter and filter holder under running water to remove the rest of the coffee (25).
With Pods (E.S.E.)
You can use E.S.E. pods to make your espresso. They can be recognised by the logo
opposite.
1 E.S.E. pod = 1 cup of espresso (19)
1. Insert the filter for coffee pods (F3) into the filter holder.
2. Place the pod as centrally as possible in the filter holder. Follow the instructions on the packaging
of the coffee pods for correct placement of the pod in the filter holder. Pods (E.S.E.) are designed
to make one cup of coffee. Using two pods on top of each other is not recommended.
3. Repeat the steps in the "With ground coffee" section, ignoring step 5.
2
button light switches on, and buttons
buttons white light will stay on. The machine
button (9), button flashes white. The machine starts to pour
white light stay on.
white light off, button orange light stay on, the machine
white light flashes,
PERSONALIZATION OF THE COFFEE VOLUME
You can personalize the coffee volume as you wish from 15 to 65 ml for 1 cup, and from 30 to 130 ml
for 2 cups.
Note : Default volume is 30 ml - 1 cup / 60 ml - 2 cups
1. The machine is in coffee brewing mode.
2. Press or for 3 seconds. Selected espresso button orange light flashes.
3. Release the button and start set coffee volume.
4. Press the button as soon as the desired volume is reached.
5. Both buttons orange lights flash 3 times to confirm the new setting.
6. The machine goes back to coffee brewing mode.
RECOVER DEFAULT COFFEE VOLUME
1. The machine is in steam pre-heat status:
2. Press for 3 seconds. The buttons
3. Water pump works once.
4. Default coffee volumes are now recovered.
5. The machine goes back to steam pre-heat status.
PERSONALIZATION OF AUTOMATIC SHUT DOWN TIME
You can change the automatic shutdown time of the machine to 5, 15 or 30 minutes. The default setting
is 30 minutes. To change it, please follow these instructions:
1. The machine is in coffee brewing mode
2. Press and hold the and buttons simultaneously for 3 seconds
3. The and button lights will flash orange:
• 1 time for a time set at 5 min
• 2 times for a time set at 15 min
• 3 times for a time set at 30 min
4. To change the current setting, press the
Repeat the operation until the number of orange flashes corresponds to the desired duration.
5. Wait until the and buttons turn white again. Your new setting is saved.
STEAM FUNCTION
Making Cappuccino
1. Make espresso as described above using big enough cups. You can remove the drip tray and
place the tall cup on the stand if required.
(26). Buttons
2. Press button white light off,
is in steam pre-heating mode.
3. Fill a container with approximately 60 to 100 ml of cold milk.
Note :
• When choosing the size of the milk container, keep in mind that the milk volume will increase by
two to three times.
• In order to obtain good quality milk foam, we recommend that you use fresh, cold milk. Pasteurised
or UHT milk usually gives the best results.
Note: For a better result, turn on the steam nozzle a few seconds in a container before using it in the
milk. It will remove the water it may contain.
button orange light stay on
orange light flashes once.
button when the and buttons are not flashing.
button orange light stay on, the machine
3