General Information; Unpacking And Inspection - MYERS DE Serie Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

General Information

DESCRIPTION
Myers submersible effluent pumps and submersible
sewage pumps are used for effluent, sewage, and waste-
water removal, and for sump drainage in residential
sewage systems. In commercial and industrial systems, use
for liquid transfer, circulation, dewatering and flood con-
trol. Dry motors are 60 Hz, 4/10 through 1 HP, 115 or 230
volt single phase. Model DSW100M4 is 460V 3 phase.
Models deliver from 27 to 42 feet of head with maximum
capacities ranging from 92 to 145 GPM. Single phase
models have built-in thermal overload protection. Three-
phase model requires external overload.
Pumps are entirely constructed of stainless steel, including
self-cleaning cast stainless steel impeller. Oil chamber pro-
vides seal protection. 1-1⁄2" and 2" solids handling capa-
bility (see "Specifications"). NBR 70 rubber lip seal with
special sand guard V-ring for better sand handling. 2" dis-
charge elbow included.

UNPACKING AND INSPECTION

Handle with care. Check items received against packing
list to be sure that all equipment has been received.
Inspect for shipping damage. If found, file claim with carri-
er immediately.
SPECIFICATIONS
Model
HP
DE40PC1
4/10
DE50PC1
1/2
DSW40P1
4/10
DSW50P1
1/2
DSW50M2
1/2
DSW100M2
1
DSW100M4
1
NOTE: For continuous duty, pump must be fully submerged in liquid with a maximum temperature of 130° F (54° C).
DIMENSIONS
Model
Operation
DE40PC1
Automatic
DE50PC1
Automatic
DSW40P1
Automatic
DSW50P1
Automatic
DSW50M2
Manual
DSW100M2
Manual
DSW100M4
Manual
Max
Load
Volts
Phase
Amps
115
1
10.5
115
1
12.0
115
1
11.0
115
1
12.0
230
1
6.0
230
1
8.0
460
3
4.0
Pump Material
Base
Housing
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
GENERAL SAFETY INFORMATION
READ AND FOLLOW SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
Warns about hazards that will cause serious
personal injury, death, or major property damage if
ignored.
Warns about hazards that can cause serious
personal injury, death, or major property damage if
ignored.
Warns about hazards that will or can cause
minor personal injury or property damage if ignored.
NOTE: Indicates special instructions which are important
but not related to hazards.
NOTE: Pump must be installed in a vertical position only.
Installing pump in any other position will void warranty.
To avoid serious injury and/or property damage, read these
rules and instructions carefully.
Check your local codes before installing. You must comply
with local codes, the National Electrical Code (NEC) in the
United States or the Canadian Electrical Code (CEC), as
applicable.
Individual Branch
Circuit Required
Discharge
(Amps)
NPT
15
15
15
15
15
15
15
Dimensions
Cover
Impeller
Height
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
304SS
Solids
Handling
Capability
Point
2"
1-1/2"
2"
1-1/2"
2"
2"
2"
2"
2"
2"
2"
2"
2"
2"
Cord
Diameter
Length
16"
9-1/2"
20'
16"
9-1/2"
20'
18"
11-1/2"
20'
18"
11-1/2"
20'
18"
11-1/2"
20'
18"
11-1/2"
20'
18"
11-1/2"
20'
2
On
Off
Point
21"
13"
21"
13"
22"
14"
22"
14"
Wt.
24 lbs.
24 lbs.
26 lbs.
26 lbs.
26 lbs.
26 lbs.
26 lbs.

Publicidad

Tabla de contenido
loading

Tabla de contenido