Bosch GDR Professional 18V-220 C Manual Original página 273

Derivative Works as a whole, provided Your use, reproduction, and
distribution of the Work otherwise complies with the conditions stated
in this License.
5. Submission of Contributions. Unless You explicitly state otherwise,
any Contribution intentionally submitted for inclusion in the Work by
You to the Licensor shall be under the terms and conditions of this
License, without any additional terms or conditions. Notwithstanding
the above, nothing herein shall supersede or modify the terms of any
separate license agreement you may have executed with Licensor
regarding such Contributions.
6. Trademarks. This License does not grant permission to use the trade
names, trademarks, service marks, or product names of the Licensor,
except as required for reasonable and customary use in describing the
origin of the Work and reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed
to in writing, Licensor provides the Work (and each Contributor
provides its Contributions) on an "AS IS" BASIS, WITHOUT
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
including, without limitation, any warranties or conditions of TITLE,
NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A
PARTICULAR PURPOSE. You are solely responsible for determining the
appropriateness of using or redistributing the Work and assume any
risks associated with Your exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether
in tort (including negligence), contract, or otherwise, unless required by
applicable law (such as deliberate and grossly negligent acts) or agreed
to in writing, shall any Contributor be liable to You for damages,
including any direct, indirect, special, incidental, or consequential
damages of any character arising as a result of this License or out of the
use or inability to use the Work (including but not limited to damages for
loss of goodwill, work stoppage, computer failure or malfunction, or any
and all other commercial damages or losses), even if such Contributor
has been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the
Work or Derivative Works thereof, You may choose to offer, and charge
a fee for, acceptance of support, warranty, indemnity, or other liability
obligations and/or rights consistent with this License. However, in
accepting such obligations, You may act only on Your own behalf and on
Your sole responsibility, not on behalf of any other Contributor, and
only if You agree to indemnify, defend, and hold each Contributor
harmless for any liability incurred by, or claims asserted against, such
Contributor by reason of your accepting any such warranty or additional
liability.
END OF TERMS AND CONDITIONS
Zlib
NanoPb, v0.3.9.2
Copyright (c) 2011 Petteri Aimonen <jpa at nanopb.mail.kapsi.fi>
This software is provided 'as-is', without any express or implied
warranty. In no event will the authors be held liable for any damages
arising from the use of this software.
Permission is granted to anyone to use this software for any purpose,
including commercial applications, and to alter it and redistribute it
freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not
claim that you wrote the original software. If you use this software in a
product, an acknowledgment in the product documentation would be
appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must
not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source
distribution.
Zlib
NanoPb, v0.3.9.9
Copyright (c) 2011 Petteri Aimonen <jpa at nanopb.mail.kapsi.fi>
Bosch Power Tools
This software is provided 'as-is', without any express or implied
warranty. In no event will the authors be held liable for any damages
arising from the use of this software.
Permission is granted to anyone to use this software for any purpose,
including commercial applications, and to alter it and redistribute it
freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not
claim that you wrote the original software. If you use this software in a
product, an acknowledgment in the product documentation would be
appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must
not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source
distribution.
None
ST Product license, vV2
COPYRIGHT 2014 STMicroelectronics
Under STMicroelectronics' intellectual property rights, the
redistribution, reproduction and use in source and binary forms of the
software or any part thereof, with or without modification, are
permitted provided that the following conditions are met:
1. Redistribution of source code (modified or not) must retain any
copyright notice, this list of conditions and the disclaimer set forth
below as items 10 and 11.
2. Redistributions in binary form, except as embedded into
microcontroller or microprocessor device manufactured by or for
STMicroelectronics or a software update for such device, must
reproduce any copyright notice provided with the binary code, this list
of conditions, and the disclaimer set forth below as items 10 and 11, in
documentation and/or other materials provided with the distribution.
3. Neither the name of STMicroelectronics nor the names of other
contributors to this software may be used to endorse or promote
products derived from this software or part thereof without specific
written permission.
4. This software or any part thereof, including modifications and/or
derivative works of this software, must be used and execute solely and
exclusively on or in combination with a microcontroller or
microprocessor device manufactured by or for STMicroelectronics.
5. No use, reproduction or redistribution of this software partially or
totally may be done in any manner that would subject this software to
any Open Source Terms. "Open Source Terms" shall mean any open
source license which requires as part of distribution of software that the
source code of such software is distributed therewith or otherwise
made available, or open source license that substantially complies with
the Open Source definition specified at www.opensource.org and any
other comparable open source license such as for example GNU
General Public License (GPL), Eclipse Public License (EPL), Apache
Software License, BSD license or MIT license.
6. STMicroelectronics has no obligation to provide any maintenance,
support or updates for the software.
7. The software is and will remain the exclusive property of
STMicroelectronics and its licensors. The recipient will not take any
action that jeopardizes STMicroelectronics and its licensors' proprietary
rights or acquire any rights in the software, except the limited rights
specified hereunder.
8. The recipient shall comply with all applicable laws and regulations
affecting the use of the software or any part thereof including any
applicable export control law or regulation.
9. Redistribution and use of this software or any part thereof other than
as permitted under this license is void and will automatically terminate
your rights under this license.
10. THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND
CONTRIBUTORS AS IS AND ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL
Licenses | 273
1 609 92A 8HZ | (14.12.2023)