Descargar Imprimir esta página

Gardena MultiControl duo Libro De Instrucciones página 20

Control de riego
Ocultar thumbs Ver también para MultiControl duo:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 54
1. Press the Menu key twice.
Start and the hours flash on the display.
2. Press the Menu button to jump to the next
programme level
– or –
change programme data with the ▼-▲ buttons
and confirm with the OK button.
When the watering duration is changed while
a program is running, the current watering
cycle is ended.
C) Manual watering:
Each valve can be opened or closed manually
at any time. A program-controlled open valve
can also be closed early without changing the
program data (watering start time, watering dura-
tion and watering frequency). The controller
must be fitted.
1. Select Valve 1 ( ï V1) or Valve 2 (V2 ð ) with
the ▼-▲ buttons.
2. [ Fig. P16 ]: Press Man.-key to open the valve
manually (or to close an open valve).
Run Time and the watering time in minutes (set
to
minutes in the works) flash for 10 seconds
30 30
on the display.
3. [ Fig. P17 ]: Whilst the watering time in minutes
is flashing, the watering duration can be modified
with the ▼-▲ button (between
(example:
minutes) and confirm with the
10 10
OK-key.
4. Press Man.-key to close the valve early.
The valve is closed.
The amended manual opening period is stored,
i. e. each time the valve is opened manually in
future the modified opening period is preset. If the
manual opening period is amended to
valve is closed and also remains closed after the
Man.-key is pressed (child lock).
5. MAINTENANCE
Clean filter [ Fig. M1 ]:
(24)
The filter
should be checked regularly and
cleaned when necessary.
1. Unscrew sleeve nut
hand from the tap thread (do not use pliers).
20
GAR_01874-20.960.11_2023-12-08.indb 20
GAR_01874-20.960.11_2023-12-08.indb 20
and
)
0:00
0:00
0:59
0:59
, the
0:00
0:00
(19)
of the Water Control by
If the valve has been manually opened and a pro-
grammed start of watering overlaps with the manual
opening duration then the watering programme will
not be carried out.
Example:
The valve is opened at 9.00 a.m. manually, the
opening period is 10 minutes. A program with
a start time between 9.00 and 9.10 a.m. will
not be undertaken in this case.
Reset [ Fig. P18 ]:
The factory settings are restored.
v Press Man.-key and Menu-key simultaneously
for 3 seconds.
All the LCD symbols are displayed for 2 seconds
and the display moves to the normal display.
• All the program data are set to zero.
• The manual watering period is set to
• The time and day of the week are retained.
Important information:
If no entry is made during programming for a period
of more than 60 seconds, the normal display reap-
pears. In this case all changes made up till now will
be applied.
If a sensor is inserted in the Water Control regis-
ters wet (wet), the corresponding programme will
not be carried out.
2. If necessary unscrew the adaptor
(24)
3. Remove filter
from sleeve nut
4. Fit the Water Control again (see 3. INITIAL
OPERATION To connect the Water Control).
again.
0:30
0:30
(18)
.
(19)
and clean.
08.12.23 11:47
08.12.23 11:47

Publicidad

loading

Este manual también es adecuado para:

1874