Publicidad
Idiomas disponibles
Idiomas disponibles
MOUNTING HEATER
TO END BRACKET
ASSEMBLY
ALIGN JUNCTION
HEATER LOCKED IN
BOX SLOT WITH
POSITION ON END
BRACKET HOOK
WALL BRACKET
Figure 2
from the left end of the cove heater and mark this location on
the back surface of the panel. Slide the center support brack-
et to the marked position on the panel, aligning the center of
the bracket with this mark.
4. To mount cove heater, attach center support bracket to the
center wall bracket by tilting the heater back and allowing the
upper slot to fall onto the bracket hook per Figure 2. Attach
the junction boxes to the end wall brackets in a similar
manor. Bring the cove heater forward to lock into place.
For 1500 to 1800 Watt Heaters:
The 1500 & 1800 watt cove heaters require the additional sup-
port of (2) center wall brackets due to the extra length. The
mounting steps are similar to the 450 to 1200 watt cove heater
with the following exceptions:
1. After the approximate center location between the end wall
brackets has been determined, measure 30 inches (762 mm)
on each side of this location to determine the approximate
location to mount the center wall brackets. Locate a stud
nearest each mark. Use these studs for the center wall
bracket locations. (Disregard original 30 inch location marks)
2. Using the provided template, align the top of the template
with the ceiling and the center of the pre-punched holes with
the bracket marks on the wall. Choosing the proper bracket
location holes, mark the bracket pilot hole locations using the
selected pre-punched holes provided on the template. With
the fasteners provided, mount the assembled end wall brack-
ets and center wall brackets to the wall. Measure the dis-
tance between the center (slot) of the left end wall bracket
and the hook of the left center wall bracket. Add 3-5/8 inches
(92 mm) to this (left end) value and record it for the left center
support bracket location on the cove heater. Determine the
distance between the center of the right end wall bracket and
the hook of the right center wall bracket. Add 3-5/8 inches
(92 mm) to this (right end) value and record it for the right
center support bracket placement on the cove heater.
3. Orient the cove heater face down on a protective flat surface.
Using the left end value recorded in step 2, measure this dis-
tance from the left end of the cove heater and mark this loca-
tion on the back surface of the panel. Using the right end
value recorded in step 2, measure this distance from the right
end of the cove heater and mark this location on the back
surface of the panel. Slide the center support brackets to the
marked positions on the panel, aligning the center of the
brackets with each mark.
4. To mount cove heater, attach center support brackets to the
center wall brackets by tilting the heater back and allowing
the upper slot to fall onto the bracket hook per Figure 2.
Attach the junction boxes to the end wall brackets in a similar
manor. Bring the cove heater forward to lock into place.
5. The cove heater can be wired from either end of the heater.
CUTAWAY SHOWING
CENTER MOUNTING
BRACKET DETAILS
TOP
FLANGE
BACK
WRAP
CENTER
SUPPORT
BRACKET
WIREWAY
END WALL
BRACKET ASSEMBLY
CENTER WALL
BRACKET
CENTER
SUPPORT
#10-16 X 1-1/2"
BRACKET
LONG SCREWS
JUNCTION BOX
ELEMENT LEAD
CROSSOVER LEAD
END CAP
#8-18 X 1" LONG SCREWS
Figure 3
Install a cable clamp (supplied by others) in one of the
knockouts located in back of the junction boxes you plan to
use. Insert the power supply cable through the cable clamp
allowing approximately 6" (152mm) of cable length to remain
inside the box to facilitate wiring. Add at least 2 inches of
cable loop between wall and knockout entering the junction
box to allow for heater expansion.
6. Refer to wiring diagrams on next page.
7. Attach end caps (found in parts bag) as shown in Figure 3.
INSTALLATION AT CORNER
Heaters must be located so that the ends of each heater are
4 inches (102 mm) from side wall. See Figure 4.
HEATER
Figure 4
OPERATING
INSTRUCTIONS
The heaters are intended to be controlled by a remote wall
mounted thermostat. The thermostat should be located in the
same room on a side wall. It should also be five feet above the
floor, but not directly under the heater.
1. Heater must be properly installed before operation.
2. Turn power supply to heater "ON" at main switch panel.
3. Where applicable, refer to control accessory instructions
regarding proper operation of any controls used with the
heater.
NOTE: For a period of time after the heaters are put into opera-
tion the owner may notice a "new smell" coming from the
heaters. This is expected on new installations and will dissipate
after approximately 24 hours of operation.
NOTE: For best results, the heater should be left "ON" constant-
ly during the heating season as the thermostat, when properly
set, will maintain the desired temperature.
3
BACK WRAP
HEAT SHIELD
COVE HEATER
FRONT PANEL
HEATER
4"
4"
Publicidad
