Makita DFR453 Manual De Instrucciones página 10

Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To start the tool, pull the switch trigger. Tool speed is
increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger, push in
the lock button and then release the trigger. To stop the
tool from the locked position, pull the switch trigger fully,
and then release it.
► Fig.7: 1. Switch trigger 2. Lock button
Reversing switch action
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
► Fig.8: 1. Reversing switch lever
Push drive mode
In push drive mode, the driver bit only rotates by apply-
ing pressure onto the driving surface with the stopper
base, allowing the tool to cut off power to the motor to
save battery power at idle.
To select push drive mode, pull the switch trigger
slightly, then release it and quickly press the mode
select button. The indicator lamp on the push drive
mode selector will then light up.
► Fig.9: 1. Mode select button 2. Indicator lamp
NOTE: Push drive mode will automatically be deacti-
vated after eight hours with the switch trigger locked
on and no further switch operation. To restart the tool,
pull the switch trigger fully to release the lock button,
and pull the trigger again.
Accidental re-start preventive
function
Even if you install the battery cartridge while pulling the
switch trigger, the tool does not start.
To start the tool, first release the switch trigger and then
pull the switch trigger.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing and removing driver bit
CAUTION:
Be careful not to touch the sharp
edges of screws while reassembling the compo-
nents and attachments.
CAUTION:
Handle accessories and attach-
ments with care. Always be sure to hold accesso-
ries and attachments body firmly when installing
and removing. Otherwise the accessories and
attachments may slip off from your hands and fall.
CAUTION:
Hold the casing when installing
and removing attachments.
CAUTION:
Always switch off and remove the
battery cartridge when changing the bit.
Installing driver bit
1. To install a driver bit, place it into the spindle hole
as far as it will go while pushing and holding the spin-
dle into the gear housing. Then release the spindle to
secure the driver bit.
► Fig.10: 1. Driver bit 2. Spindle 3. Gear housing
2. Push the casing into the gear housing while hold-
ing the body of the casing firmly until the release but-
tons on each side of the casing lock in place with a little
click.
► Fig.11: 1. Casing 2. Release buttons
Removing driver bit
1. Press and hold the release buttons on each side
of the casing, and then pull the casing apart.
► Fig.12: 1. Release buttons 2. Casing
2.
To remove the driver bit, pull it off while pushing
and holding the spindle into the gear housing.
► Fig.13: 1. Driver bit 2. Spindle 3. Gear housing
Installing screw strip
CAUTION:
Always switch off and remove the
battery cartridge when cutting the screw strip.
Insert a screw strip through the screw strip guide on
the casing, and then insert it through the screw loading
guide in the feeder box.
► Fig.14: 1. Screw strip 2. Screw strip guide 3. Casing
4. Screw loading guide 5. Feeder box
NOTICE:
Make sure to set the first screw in the
second row next to the driving position.
► Fig.15: 1. First screw 2. Driving position
10 ENGLISH