Publicidad
Idiomas disponibles
Idiomas disponibles
Wear non-slip safety footwear when
using the product.
Beware of chainsaw kickback and
avoid contact with bar tip.
Do not expose the product to rain or
damp conditions.
Do not operate the saw using only
one hand.
Hold and operate the saw properly
with both hands.
Set the chain brake to the RUN
position.
Set the chain brake to the BRAKE
position.
XX
Guaranteed sound power level
Do not dispose of waste batteries,
waste electrical and electronic
equipment as unsorted municipal
waste. Waste batteries and waste
electrical and electronic equipment
must be collected separately. Waste
batteries, waste accumulators, and
light sources have to be removed from
the equipment. Check with your local
authority or retailer for recycling advice
and collection point. According to local
regulations, retailers may have an
obligation to take back waste batteries
and waste electrical and electronic
equipment free of charge. Your
contribution to the reuse and recycling
of waste batteries and waste electrical
and electronic equipment helps to
reduce the demand of raw materials.
Waste batteries, in particular
containing lithium, and waste electrical
and electronic equipment contain
valuable and recyclable materials,
which can adversely impact the
environment and the human health if
not disposed of in an environmentally
compatible manner. Delete personal
data from waste equipment, if any.
GETTING STARTED
See pages 212-213.
1. Wear Personal Protective Equipment (PPE).
Wear full eye protection, ear protection, non-slip heavy-
duty gloves, substantial footwear, and protective clothing
at all times while operating the product. Do not operate
the product when barefoot or wearing open sandals.
2. Loosen the bar mounting nuts. Remove the nuts and
sprocket cover.
3. Place the chain drive links into the bar groove. Position
the chain so that there is a loop at the back of the bar.
The saw chain should face in the direction of chain
rotation. If the chain faces backwards, turn the loop over.
4. Hold the chain in position on the bar, and place the loop
around the drive sprocket. Lower the bar so that the
bolts go through the slot in the bar.
Reinstall the sprocket cover. Install and hand-tighten the
bar mounting nuts. The guide bar must be free to move
for chain tension adjustment.
5. Adjust the chain tension. Turn the chain tensioning
screw using the combination wrench. Frequently check
the chain tension while adjusting.
To increase the chain tension, turn the chain
–
tensioning screw clockwise.
To reduce the chain tension, turn the chain tensioning
–
screw counterclockwise.
NOTE: The chain tension is correct when the gap
between the cutter in the chain and the bar is between
7.6 and 8.6 mm. Pull the chain in the middle of the lower
side of the bar downwards (away from the bar), and
measure the distance between the bar and the chain
cutters.
NOTE: The temperature of the chain increases during
normal operation, causing the chain to stretch. Check
the chain tension frequently and adjust as required. A
chain that is tensioned while warm may be too tight upon
cooling. Make sure that the chain tension is correctly
adjusted as specified in these instructions.
6. Hold up the tip of the guide bar, and securely tighten the
bar mounting nuts.
7. Add chain lubricating oil.
Use only RYOBI chainsaw lubricating oil from an
authorised service centre.
Clear the surface around the oil cap to prevent
contamination. Remove the cap from the oil tank. Pour
the oil into the oil tank, and monitor the oil level gauge.
Ensure that no dirt enters the oil tank while filling. Close
the oil tank, and tighten the cap. Wipe off any spillage.
NOTE: Never work without chain lubricant. If the saw chain
is running without lubricant, the guide bar and the saw chain
can be damaged. Before and while using the chainsaw,
check the oil level in the oil level gauge.
8. Install the battery pack.
Align the raised ribs on the battery pack with the grooves
in the product's battery port. Insert the battery pack into
the product. Make sure that the latch of the battery pack
snaps in place and that the battery pack is fully seated
and securely attached before beginning operation.
WARNING! Always hold the product with the right hand
on the rear handle and the left hand on the front handle.
WARNING! Grip both handles with the thumbs and
fi ngers encircling the handles. Ensure that the left hand is
holding the front handle so that the thumb is underneath.
9. Start the product.
Set the chain brake into the run position by grasping the
top of the chain brake lever and pulling towards the front
handle until you hear a click. Pull the trigger release.
Press the switch trigger.
NOTE: To stop the product, engage the chain brake by
rotating the left hand around the front handle. Allow the back
of the hand to push the chain brake lever towards the bar
while the chain is rotating rapidly. Release the switch trigger.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
9
Publicidad
