Peg-Perego siesta Instrucciones De Uso página 8

ABLE TO SIT UP ALONE.
_ THE RECLINER IS NOT DESIGNED
FOR LONG PERIODS OF SLEEP.
IT SHOULD NOT BE USED AS A
SUBSTITUTE FOR A COT. IF THE
CHILD NEEDS TO SLEEP, HE/
SHE SHOULD BE PLACED IN A
SUITABLE COT.
_ DANGER OF STRANGULATION:
NEVER LEAVE THE CHILD IN THE
RECLINER IF THE SAFETY HARNESS
IS LOOSE OR UNDONE.
_ RISK OF FALLING: IT IS DANGEROUS
TO USE THE RECLINED CRADLE ON
A RAISED SURFACE.
A single product which follows the growth
of your child.
_ From 0 to 6 months, a comfortable reclined
cradle;
_ From the age of 6 months, a high chair for
eating, playing and relaxing.
_ From the age of 12 months, a high chair without
a tray, for sitting at the table with the adults.
The images referring to the textile details
may differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS FOR USE
1 OPENING: Before opening the high chair,
fit the rear wheels by pushing them in the
direction of the arrow (fig_a). Lift the seat
(fig_b), press the red buttons (fig_c) and
open the high chair (fig_d).
2 TRAY: To fit the tray, pull the central lever
underneath it towards you while at the same
time pushing it all the way into the armrests
(fig_a). To extend or remove the tray, pull
the central lever underneath it towards you
(fig_b) and move it outwards (fig_c). To
remove the tray, pull the side levers outwards
and pull the tray towards you. The high chair
has a double tray. The top tray can be easily
washed in a dishwasher. To remove it, detach
it from the lower tray and lift it up (fig. d).
3 ADJUSTING THE HEIGHT: The seat can be set
at 9 different heights. To raise or lower the
seat, pull the two levers upwards (fig. a) and
move it to the required position. The handle
under the netting can also be used to raise
the seat (fig_b). This can also be done with
the child in the high chair.
RECLINING BACKREST: The seat can be
reclined in 5 positions. To adjust it, raise the
handle behind the backrest (fig. c) and lock
it in the required position. This can also be
done with the child in the high chair.
4 BRAKE: The brake on the high chair is
always enabled. To move the chair, keep
both buttons held down. To keep the chair
unlocked, press both buttons and slide the
levers placed on the buttons until they lock
into position.
5 ADJUSTABLE FOOTREST: The footrest can be
set in 3 positions. To raise it, push it upwards.
To lower it, push in the two levers and move
the footrest down (fig_b).
6 FIVE-POINT SAFETY HARNESS: To fasten the
safety harness, push the two waist strap
buckles (with the shoulder straps attached)
into the leg divider until they click into
position (fig_a). To release it, press the center
of the buckle while pulling the waist strap
outwards (fig_b). To tighten the waist strap,
pull the ends on both sides. To loosen it, do
the opposite.
7 The shoulder straps of the harness can be set
at two different heights. Partially remove the
fabric covering (fig_a), release the shoulder
straps from the backrest (fig_b) and pull
them out from the fabric covering. Insert
the ends of the shoulder straps in the other
slots in the fabric covering and the backrest
(fig_c), then put the fabric covering back into
the right position on the backrest.
8 USE WITHOUT THE TRAY: to use the seat at
the table, remove the tray. To clip the tray on
the rear supports of the high chair, align and
engage it with the attachments (fig_b).
9 CLOSING AND REOPENING THE TRAY: Pull the
central lever underneath the tray towards
you (fig_a) and extend it as far as the red
markers (fig_b), then swing it upwards to lock
it in place (fig_c). To reopen the tray, press
the lever under the armrest (fig_d), swing
it downwards, then pull the central lever
towards you and put the tray in one of the
positions for use.
10 FOLDING UP: Before folding up the high
chair, ensure that the wheels are facing
inwards (fig_a). Press the red buttons (fig_b)
and fold up the high chair (fig_c). Fig_d
shows a folded up high chair.
11 REMOVABLE COVERS: To remove the covers of
the seat, pull off the upper part of the fabric
covering and pull the harness straps through
the backrest (fig_a) and the fabric covering
(fig_b). Lower the backrest and pull out the
leg divider strap from under the seat (fig_c).
12 Unbutton the sack at the sides (fig. a) and
pull up to remove it (fig. b).
SERIAL NUMBERS
13 Information about the production date of the
SIESTA can be found on the seat.
_ Product name, date of manufacture and serial
number.
- 8 -